1. Shut off power to the garbage disposal and detach the down catch.
Turn off the electrical power at the circuit box or breaker. After that, making use of adjustable pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Support the garbage disposal with one hand and put the end of the wrenchette or screwdriver right into the ideal side of one mounting lug on the reduced installing ring. Raise the garbage disposal a little and loosen the lower mounting ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is devoid of the placing assembly.
3. Detach the electric.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen up the green ground screw and eliminate cable ports. Separate garbage disposal cords from electric supply wires. Loosen up screws on the electric clamp port and remove cables from the garbage disposal.
4. Get rid of existing installing equipment if equipment replacement required. Or else skip to step 12.
To get rid of the existing installing equipment, loosen the 3 mounting screws, tear the snap ring off with a screwdriver as well as get rid of the old placing assembly.
5. Remove the old sink flange as well as putty.
Push the old sink flange up via the sink opening. Utilize a screwdriver or putty blade to carefully scrape all old putty from the side of the sink hole
. Set up the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange right into the drainpipe opening and also press it into location. Placing a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in position while placing the sink flange to the sink. To stay clear of scratching your sink or the flange, position a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these items in place.
7. Get rid of the dishwasher knockout plug.
If utilizing a dishwashing machine, you will certainly need to tap out the dishwasher knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired System:
Turn the garbage disposal over and eliminate electrical cover plate. Pull out wires. Place cord adapter (not consisted of) and run electric cable through gain access to opening on base of garbage disposal. Tighten cable television adapter. Push cables right into garbage disposal (do not displace cardboard shield) and replace electrical cover plate.
If you have a hardwired device as well as you’re looking to connect a cord, you will require a power cord kit.
Corded System:
For a garbage disposal with a factory-installed cord, just plug in to the outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower placing ring till all 3 tabs are locked into the placing setting up. The garbage disposal will currently hang by itself.
10. Put the discharge tube.
Put the discharge tube into the discharge coupler, then slide the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain catch.
Rotate the garbage disposal to ensure that the discharge tube is aligned with the drain catch. If the discharge tube is also long, cut off as high as needed. If it is too brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwashing machine, it might be attached via an air void. Use a hose clamp to connect the drain tube to the dishwashing machine inlet. Now that everything is set up as well as in position, lock the garbage disposal to the sink mounting setting up making use of the wrenchette that included the unit. For Development versions, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it right into the sink till it snaps right into place.
13. Examine the garbage disposal.
For all models, you ought to check for leakages at the sink flange, dishwasher, tail-pipe and mounting assembly connections. Ultimately, switch on the electric breaker to evaluate its procedure.
How to Install a Garbage Disposal in Midway City
How to Install a Garbage Disposal in Midway City