1. Separate the p-trap and the horizontal extension pipe.
Big channel-lock pliers or a monkey wrench work well to loosen the nuts holding the pipes with each other. When both links are cost-free, eliminate the parts. You may intend to clean up the straight drain pipeline to get rid of any kind of possible blockage. (This is not required in new construction.).
2. Separate the down drainpipe.
Using big channel-lock pliers, separate the down drain coming from the sink and also the connection that attaches it to the p-trap. When both connections are free, eliminate the components.
3. Loosen the huge nut.
Loosen the big nut that holds the strainer in place beneath the sink. Get rid of the strainer body.
4. Tear off the snap ring and also wipe the old plumber’s putty.
Utilizing a flathead screwdriver, loosen the 3 screws on the placing assembly as well as tear off the snap ring. Clean off the old plumber’s putty that surrounds the edge of the drain opening.
5. Set up the brand-new sink flange.
Area a 1/2″ rope of plumber’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drain opening as well as press it into area. Putting a weight, such as your garbage disposal, in addition to the sink flange will certainly help hold the sink flange in place while placing it to the sink. To stay clear of scraping your sink or the flange, position a towel between the sink surface as well as the weight.
6. Mount gasket and flanges.
From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in position.
7. Slip on the installing as well as snap rings.
Next off, slip on the mounting ring and also snap ring. Tighten the 3 placing screws, alternately tightening each screw a few turns at once up until the installing assembly is equally as well as tightly seated against all-time low of the sink.
8. Eliminate the dish washer knockout plug.
If using a dishwashing machine, you will certainly require to tap out the dishwasher ko plug. Lay the garbage disposal on its side and also use a screwdriver as well as hammer to touch it out. Next, remove the loose ko plug from inside the garbage disposal.
9. Attach the electric.
Hardwired Unit:.
Turn the garbage disposal over and eliminate electric cover plate. Take out cables. Put cord port (not included) as well as run electrical cable via access opening on base of garbage disposal. Tighten up wire port. Push wires right into garbage disposal (do not displace cardboard shield) and change electrical cover plate.
If you have a hardwired unit and you’re looking to affix a cord, you will require a power cable kit.
Corded Device:.
For a garbage disposal with a factory-installed cable, simply connect in to the electrical outlet under your sink after finishing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced installing ring till all three tabs are locked right into the placing assembly.
11. Put the discharge tube.
Place the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drain pipe.
Revolve the garbage disposal so that the discharge tube is straightened with the drainpipe trap. If the discharge tube is too long, cut off as a lot of the tube as required. If it is as well brief, you can acquire an expansion. If you are attaching the garbage disposal to a dishwasher, it may be attached with an air void. Use a tube clamp to affix the drainpipe pipe to the dishwashing machine inlet.
13. Lock the garbage disposal in place.
Now that every little thing is set up and ready, lock the garbage disposal to the sink placing setting up making use of the wrench that featured the unit. Put the Quiet Collar Sink Baffle into the sink opening by pressing it into the sink until it snaps right into area.
14. Evaluate the garbage disposal.
Test for leakages at the sink flange, dish washer, tail-pipe and also installing setting up links. Ultimately, turn on the electrical breaker to check its procedure. Appreciate your new garbage disposal!
How to Install a Garbage Disposal in Midway City