1. Switch off power to the garbage disposal and also separate the down catch.
Turn off the electric power at the fuse box or circuit breaker. After that, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand as well as insert completion of the wrenchette or screwdriver into the ideal side of one installing lug on the reduced installing ring. Raise the garbage disposal slightly and also loosen up the reduced placing ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the mounting setting up.
3. Separate the electric.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen up the green ground screw and get rid of cable ports. Detach garbage disposal cables from electric supply cords. Loosen up screws on the electrical clamp adapter and get rid of cords from the garbage disposal.
4. Get rid of existing mounting hardware if hardware substitute needed. Or else miss to step 12.
To remove the existing placing equipment, loosen the 3 placing screws, tear the breeze ring off with a screwdriver and also eliminate the old placing setting up.
5. Remove the old sink flange and also putty.
Press the old sink flange up via the sink hole. Utilize a screwdriver or putty knife to very carefully scrape all old putty from the side of the sink hole
. Mount the brand-new sink flange, gasket and also rings.
Location a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange right into the drainpipe opening and press it into area. Putting a weight, such as the garbage disposal, in addition to the sink flange will aid hold the sink flange in place while installing the sink flange to the sink. To stay clear of damaging your sink or the flange, put a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these pieces in position.
7. Remove the dishwashing machine knockout plug.
If utilizing a dishwasher, you will require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and use a screwdriver as well as hammer to touch it out. Next, get rid of the loosened knockout plug from inside the garbage disposal.
8. Attach the electric.
Hardwired System:
Transform the garbage disposal over as well as get rid of electric cover plate. Pull out cords. Insert cable adapter (not included) and run electric cable television with accessibility opening on base of garbage disposal. Tighten up wire port. Press cables into garbage disposal (do not displace cardboard shield) and also replace electrical cover plate.
If you have a hardwired device and also you’re aiming to attach a cord, you will certainly need a power cable package.
Corded System:
For a garbage disposal with a factory-installed cord, just plug in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the lower placing ring up until all 3 tabs are secured right into the mounting assembly. The garbage disposal will currently hang by itself.
10. Place the discharge tube.
Insert the discharge tube into the discharge coupler, then move the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain trap.
Rotate the garbage disposal to make sure that the discharge tube is lined up with the drainpipe catch. If the discharge tube is also long, removed as high as necessary. If it is too short, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwasher, it may be connected via an air void. Utilize a hose clamp to connect the drainpipe tube to the dish washer inlet. Since everything is set up as well as in position, lock the garbage disposal to the sink mounting setting up making use of the wrenchette that included the system. For Advancement versions, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink till it snaps right into area.
13. Evaluate the garbage disposal.
For all models, you should test for leakages at the sink flange, dishwasher, tail-pipe and also mounting assembly connections. Ultimately, turn on the electrical breaker to evaluate its operation.
Starting a Garbage Disposal Installation Project in Rowland Heights
How to Choose a Garbage Disposal in Rowland Heights