1. Separate the p-trap and also the straight expansion pipeline.
Large channel-lock pliers or a pipe wrench job well to loosen the nuts holding the pipes together. When both connections are complimentary, remove the components. You may want to cleanse the horizontal drainpipe pipe to remove any type of feasible obstruction. (This is not essential in brand-new building.).
2. Disconnect the down drain.
Making use of huge channel-lock pliers, detach the down drainpipe coming from the sink as well as the link that connects it to the p-trap. When both links are cost-free, eliminate the parts.
3. Unscrew the huge nut.
Loosen the huge nut that holds the filter in place beneath the sink. Get rid of the strainer body.
4. Pry off the snap ring and clean off the old plumber’s putty.
Making use of a flathead screwdriver, loosen up the 3 screws on the mounting setting up and also pry off the snap ring. Wipe the old plumber’s putty that borders the side of the drain opening.
5. Set up the brand-new sink flange.
Location a 1/2″ rope of plumber’s putty around the drainpipe opening in the sink. Drop the new sink flange into the drain opening and press it into location. Putting a weight, such as your garbage disposal, in addition to the sink flange will help hold the sink flange in place while installing it to the sink. To stay clear of scraping your sink or the flange, position a towel between the sink surface as well as the weight.
6. Set up gasket and flanges.
From under the sink, slide the fiber gasket, back-up flange as well as placing flange over the sink flange. Hold these pieces in place.
7. Slip on the mounting and break rings.
Next off, slip on the installing ring and also snap ring. Tighten the 3 installing screws, alternately tightening up each screw a few turns at once up until the installing assembly is evenly and also snugly seated against all-time low of the sink.
8. Get rid of the dish washer ko plug.
If utilizing a dishwashing machine, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side as well as utilize a screwdriver and hammer to tap it out. Next off, remove the loose knockout plug from inside the garbage disposal.
9. Link the electrical.
Hardwired System:.
Transform the garbage disposal over as well as get rid of electrical cover plate. Take out cables. Put cable television connector (not consisted of) as well as run electric cord via gain access to hole on bottom of garbage disposal. Tighten up cord port. Push wires right into garbage disposal (do not displace cardboard guard) as well as change electric cover plate.
If you have a hardwired device as well as you’re aiming to connect a cord, you will need a power cord package.
Corded Unit:.
For a garbage disposal with a factory-installed cord, just plug in to the outlet under your sink after completing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the lower placing ring until all 3 tabs are locked right into the installing assembly.
11. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drainpipe pipeline.
Turn the garbage disposal so that the discharge tube is lined up with the drain trap. If the discharge tube is as well long, removed as much of the tube as necessary. If it is also brief, you can buy an extension. If you are attaching the garbage disposal to a dishwasher, it might be connected through an air space. Use a tube clamp to connect the drainpipe hose to the dishwasher inlet.
13. Lock the garbage disposal in position.
Now that everything is installed and ready, secure the garbage disposal to the sink installing setting up utilizing the wrench that included the device. Place the Quiet Collar Sink Baffle into the sink opening by pressing it into the sink up until it snaps right into location.
14. Test the garbage disposal.
Test for leaks at the sink flange, dish washer, tail-pipe as well as placing setting up links. Finally, turn on the electric breaker to test its operation. Enjoy your new garbage disposal!
DIY Garbage Disposal Installation in Santa Fe Springs