1. Switch off power to the garbage disposal and also separate the down trap.
Turn off the electric power at the circuit box or circuit breaker. Then, using adjustable pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also insert the end of the wrenchette or screwdriver right into the ideal side of one placing lug on the lower installing ring. Raise the garbage disposal somewhat as well as loosen up the reduced placing ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is without the mounting setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side as well as get rid of the electrical cover plate from all-time low. Loosen the eco-friendly ground screw and also get rid of wire adapters. Separate garbage disposal cords from electric supply wires. Loosen up screws on the electric clamp port and eliminate cables from the garbage disposal.
4. Get rid of existing installing equipment if hardware replacement needed. Or else miss to tip 12.
To get rid of the existing mounting hardware, loosen the 3 mounting screws, tear the snap ring off with a screwdriver as well as remove the old placing assembly.
5. Get rid of the old sink flange and putty.
Press the old sink flange up via the sink hole. Make use of a screwdriver or putty blade to thoroughly scrape all old putty from the edge of the sink opening
. Install the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drain opening and also press it right into location. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in place while mounting the sink flange to the sink. To avoid scraping your sink or the flange, position a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange and placing flange over the sink flange. Hold these items in position.
7. Eliminate the dishwashing machine knockout plug.
If making use of a dish washer, you will certainly need to touch out the dish washer knockout plug. Lay the garbage disposal on its side and utilize a screwdriver as well as hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Transform the garbage disposal over and remove electric cover plate. Take out wires. Put cable television connector (not included) and also run electrical cable via accessibility opening on bottom of garbage disposal. Tighten cord connector. Push cables into garbage disposal (do not displace cardboard shield) and replace electric cover plate.
If you have a hardwired unit and also you’re looking to connect a cord, you will require a power cord set.
Corded System:
For a garbage disposal with a factory-installed cord, just connect in to the electrical outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the lower mounting ring up until all 3 tabs are secured into the placing assembly. The garbage disposal will currently hang by itself.
10. Put the discharge tube.
Place the discharge tube into the discharge coupler, then move the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain trap.
Turn the garbage disposal to ensure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is also long, removed as long as required. If it is also short, you can buy an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dish washer, it may be connected with an air gap. Utilize a hose pipe clamp to affix the drain hose to the dishwasher inlet. Since whatever is set up and in position, lock the garbage disposal to the sink installing assembly utilizing the wrenchette that came with the device. For Evolution models, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink up until it breaks into area.
13. Check the garbage disposal.
For all models, you ought to check for leakages at the sink flange, dish washer, tail-pipe and also mounting setting up links. Finally, switch on the electric breaker to evaluate its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Corona
Ways to Install a Garbage Disposal in Corona