1. Turn off power to the garbage disposal and also disconnect the down catch.
Shut off the electrical power at the fuse box or circuit breaker. After that, using flexible pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also place completion of the wrenchette or screwdriver right into the right side of one installing lug on the reduced installing ring. Lift the garbage disposal a little and loosen the reduced placing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the mounting assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side as well as remove the electrical cover plate from all-time low. Loosen up the environment-friendly ground screw and get rid of cable ports. Disconnect garbage disposal cords from electric supply wires. Loosen screws on the electric clamp connector and also eliminate cords from the garbage disposal.
4. Eliminate existing mounting hardware if hardware substitute needed. Or else miss to step 12.
To eliminate the existing installing hardware, loosen the three installing screws, tear the breeze ring off with a screwdriver and get rid of the old mounting assembly.
5. Get rid of the old sink flange as well as putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty knife to very carefully scratch all old putty from the edge of the sink hole
. Install the brand-new sink flange, gasket and rings.
Place a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange into the drainpipe opening and also press it right into place. Positioning a weight, such as the garbage disposal, on top of the sink flange will certainly help hold the sink flange in position while mounting the sink flange to the sink. To stay clear of scratching your sink or the flange, position a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these pieces in position.
7. Get rid of the dishwashing machine ko plug.
If utilizing a dish washer, you will need to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and also hammer to tap it out. Next off, get rid of the loose knockout plug from inside the garbage disposal.
8. Connect the electric.
Hardwired System:
Turn the garbage disposal over and also remove electric cover plate. Pull out cables. Place wire adapter (not consisted of) and run electric cable television through gain access to hole on bottom of garbage disposal. Tighten up wire adapter. Push wires into garbage disposal (do not displace cardboard shield) and change electrical cover plate.
If you have a hardwired unit as well as you’re wanting to attach a cable, you will need a power cable package.
Corded Unit:
For a garbage disposal with a factory-installed cord, just connect in to the outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the reduced mounting ring until all 3 tabs are locked right into the placing assembly. The garbage disposal will currently hang on its own.
10. Put the discharge tube.
Put the discharge tube into the discharge coupler, then move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Rotate the garbage disposal so that the discharge tube is lined up with the drain trap. If the discharge tube is too long, cut off as much as required. If it is as well short, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dish washer, it might be linked through an air void. Utilize a hose pipe clamp to connect the drainpipe hose pipe to the dish washer inlet. Since whatever is set up as well as in position, secure the garbage disposal to the sink mounting assembly using the wrenchette that included the device. For Evolution models, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink up until it breaks right into place.
13. Check the garbage disposal.
For all models, you ought to check for leaks at the sink flange, dishwasher, tail-pipe and placing setting up connections. Finally, turn on the electrical breaker to evaluate its operation.
How to Choose a Garbage Disposal in Valencia