1. Disconnect the p-trap and the straight expansion pipe.
Big channel-lock pliers or a pipe wrench work well to loosen up the nuts holding the pipes with each other. When both connections are complimentary, get rid of the components. You might want to cleanse the straight drainpipe pipeline to get rid of any kind of possible blockage. (This is not essential in new building and construction.).
2. Separate the down drain.
Making use of big channel-lock pliers, separate the down drain coming from the sink and also the connection that attaches it to the p-trap. When both links are cost-free, get rid of the parts.
3. Unscrew the large nut.
Unscrew the huge nut that holds the strainer in place underneath the sink. Get rid of the filter body.
4. Tear off the breeze ring and also clean off the old plumbing’s putty.
Using a flathead screwdriver, loosen up the 3 screws on the installing setting up as well as pry off the snap ring. Wipe the old plumbing’s putty that surrounds the side of the drainpipe opening.
5. Mount the new sink flange.
Location a 1/2″ rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into area. Placing a weight, such as your garbage disposal, in addition to the sink flange will assist hold the sink flange in position while installing it to the sink. To prevent damaging your sink or the flange, place a towel in between the sink surface area and the weight.
6. Set up gasket and also flanges.
From under the sink, slide the fiber gasket, backup flange and placing flange over the sink flange. Hold these items in position.
7. Slip on the mounting and break rings.
Next, slip on the installing ring as well as break ring. Tighten the three mounting screws, at the same time tightening up each screw a few turns at once till the mounting assembly is uniformly as well as tightly seated against the bottom of the sink.
8. Remove the dishwasher ko plug.
If using a dishwasher, you will require to touch out the dish washer knockout plug. Lay the garbage disposal on its side and use a screwdriver and also hammer to touch it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
9. Attach the electric.
Hardwired Unit:.
Transform the garbage disposal over and eliminate electric cover plate. Pull out cables. Insert cable adapter (not included) as well as run electric cord via accessibility opening on bottom of garbage disposal. Tighten cable port. Press cables right into garbage disposal (do not displace cardboard shield) as well as change electrical cover plate.
If you have a hardwired unit and also you’re looking to connect a cord, you will certainly require a power cord set.
Corded Device:.
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after completing the remainder of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the lower installing ring up until all three tabs are locked right into the installing setting up.
11. Insert the discharge tube.
Place the discharge tube into the discharge coupler, then move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drain pipe.
Rotate the garbage disposal so that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, cut off as a lot of television as necessary. If it is as well brief, you can purchase an extension. If you are linking the garbage disposal to a dish washer, it might be attached through an air space. Use a hose pipe clamp to connect the drainpipe tube to the dishwasher inlet.
13. Lock the garbage disposal in place.
Now that everything is installed and ready, lock the garbage disposal to the sink placing assembly making use of the wrench that included the device. Place the Quiet Collar Sink Baffle right into the sink opening by pressing it right into the sink until it breaks right into location.
14. Evaluate the garbage disposal.
Test for leakages at the sink flange, dishwasher, tail-pipe as well as placing setting up connections. Finally, turn on the electric breaker to test its procedure. Enjoy your new garbage disposal!
Installing a Replacement Garbage Disposal in Diamond Bar