1. Detach the p-trap and the horizontal extension pipe.
Huge channel-lock pliers or a pipe wrench work well to loosen the nuts holding the pipes with each other. When both links are totally free, get rid of the components. You may want to clean the horizontal drain pipeline to eliminate any possible blockage. (This is not necessary in brand-new building and construction.).
2. Separate the down drain.
Using large channel-lock pliers, detach the down drain originating from the sink as well as the connection that connects it to the p-trap. When both connections are totally free, remove the components.
3. Loosen the huge nut.
Loosen the huge nut that holds the filter in place beneath the sink. Eliminate the strainer body.
4. Tear off the snap ring and also clean off the old plumbing technician’s putty.
Using a flathead screwdriver, loosen up the 3 screws on the mounting setting up as well as pry off the snap ring. Clean off the old plumber’s putty that borders the side of the drainpipe opening.
5. Install the new sink flange.
Location a 1/2″ rope of plumbing technician’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange right into the drain opening as well as press it right into place. Putting a weight, such as your garbage disposal, in addition to the sink flange will certainly assist hold the sink flange in place while installing it to the sink. To stay clear of damaging your sink or the flange, position a towel between the sink surface area as well as the weight.
6. Mount gasket as well as flanges.
From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these pieces in place.
7. Slip on the placing and also snap rings.
Next off, slip on the mounting ring and also snap ring. Tighten up the three placing screws, alternately tightening up each screw a few turns at once until the placing assembly is uniformly as well as tightly seated against the bottom of the sink.
8. Eliminate the dishwashing machine ko plug.
If making use of a dishwashing machine, you will certainly require to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side as well as utilize a screwdriver and hammer to tap it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
9. Connect the electric.
Hardwired System:.
Turn the garbage disposal over as well as eliminate electrical cover plate. Pull out cords. Place cable connector (not consisted of) as well as run electric cable through access hole on bottom of garbage disposal. Tighten up cable adapter. Push wires into garbage disposal (do not displace cardboard guard) and change electric cover plate.
If you have a hardwired device as well as you’re aiming to attach a cable, you will certainly require a power cable kit.
Corded Unit:.
For a garbage disposal with a factory-installed cord, simply plug in to the outlet under your sink after completing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, turn the lower placing ring up until all three tabs are secured into the mounting setting up.
11. Put the discharge tube.
Insert the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drain pipe.
Turn the garbage disposal to make sure that the discharge tube is aligned with the drain catch. If the discharge tube is as well long, cut off as a lot of television as essential. If it is too brief, you can acquire an extension. If you are connecting the garbage disposal to a dishwashing machine, it may be connected through an air void. Make use of a hose clamp to affix the drainpipe hose to the dish washer inlet.
13. Lock the garbage disposal in place.
Now that every little thing is installed and also in position, secure the garbage disposal to the sink placing assembly making use of the wrench that included the device. Put the Quiet Collar Sink Baffle into the sink opening by pressing it into the sink until it snaps right into place.
14. Test the garbage disposal.
Test for leakages at the sink flange, dishwashing machine, tail-pipe as well as installing assembly connections. Lastly, turn on the electric breaker to evaluate its operation. Appreciate your brand-new garbage disposal!
New Garbage Disposal Installation Guide in Hacienda Heights