1. Disconnect the p-trap and also the horizontal expansion pipe.
Big channel-lock pliers or a monkey wrench work well to loosen the nuts holding the pipes together. When both connections are totally free, get rid of the parts. You may wish to cleanse the horizontal drain pipe to remove any type of possible obstruction. (This is not necessary in brand-new construction.).
2. Disconnect the down drain.
Utilizing large channel-lock pliers, disconnect the down drainpipe originating from the sink as well as the link that attaches it to the p-trap. When both connections are cost-free, eliminate the components.
3. Loosen the huge nut.
Loosen the huge nut that holds the filter in position underneath the sink. Eliminate the filter body.
4. Pry off the breeze ring and also clean off the old plumbing professional’s putty.
Making use of a flathead screwdriver, loosen the 3 screws on the mounting setting up and pry off the breeze ring. Wipe the old plumbing technician’s putty that borders the edge of the drain opening.
5. Install the new sink flange.
Place a 1/2″ rope of plumber’s putty around the drain opening in the sink. Go down the brand-new sink flange right into the drainpipe opening as well as press it into place. Positioning a weight, such as your garbage disposal, on top of the sink flange will aid hold the sink flange in position while installing it to the sink. To prevent scraping your sink or the flange, put a towel between the sink surface area as well as the weight.
6. Mount gasket and also flanges.
From under the sink, slide the fiber gasket, backup flange and also placing flange over the sink flange. Hold these items in place.
7. Slip on the mounting as well as snap rings.
Next, slip on the mounting ring and also break ring. Tighten up the three installing screws, alternately tightening each screw a couple of turns each time until the mounting assembly is equally as well as securely seated versus the bottom of the sink.
8. Remove the dish washer knockout plug.
If utilizing a dishwashing machine, you will certainly require to touch out the dish washer knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and also hammer to tap it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
9. Connect the electric.
Hardwired Unit:.
Transform the garbage disposal over and remove electric cover plate. Pull out cables. Insert cord port (not consisted of) and also run electric cable television with access hole on base of garbage disposal. Tighten cable port. Push cords into garbage disposal (do not displace cardboard shield) as well as replace electric cover plate.
If you have a hardwired device as well as you’re looking to connect a cord, you will need a power cable package.
Corded System:.
For a garbage disposal with a factory-installed cord, simply plug in to the electrical outlet under your sink after completing the remainder of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the reduced installing ring until all three tabs are locked into the mounting assembly.
11. Put the discharge tube.
Insert the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
12. Align the discharge tube with the drainpipe pipe.
Rotate the garbage disposal to ensure that the discharge tube is straightened with the drainpipe catch. If the discharge tube is also long, cut off as a lot of television as necessary. If it is too brief, you can buy an extension. If you are connecting the garbage disposal to a dishwasher, it may be connected through an air gap. Use a tube clamp to connect the drain hose pipe to the dishwasher inlet.
13. Lock the garbage disposal in position.
Now that every little thing is installed and also in position, secure the garbage disposal to the sink installing assembly using the wrench that came with the device. Put the Quiet Collar Sink Baffle right into the sink opening by pressing it into the sink until it snaps right into location.
14. Examine the garbage disposal.
Examination for leakages at the sink flange, dishwashing machine, tail-pipe and installing setting up links. Lastly, switch on the electric breaker to test its operation. Enjoy your new garbage disposal!
What to Think About During Garbage Disposal Installation in Ontario