1. Disconnect the p-trap and also the straight extension pipe.
Large channel-lock pliers or a monkey wrench work well to loosen up the nuts holding the pipelines with each other. When both connections are totally free, eliminate the parts. You may intend to clean up the horizontal drain pipeline to remove any type of feasible obstruction. (This is not required in new building.).
2. Disconnect the down drain.
Using large channel-lock pliers, detach the down drainpipe coming from the sink and the connection that connects it to the p-trap. When both links are totally free, eliminate the components.
3. Loosen the huge nut.
Unscrew the huge nut that holds the strainer in place below the sink. Get rid of the filter body.
4. Tear off the breeze ring as well as clean off the old plumbing professional’s putty.
Making use of a flathead screwdriver, loosen up the 3 screws on the installing assembly and tear off the breeze ring. Clean off the old plumbing professional’s putty that surrounds the side of the drain opening.
5. Set up the new sink flange.
Location a 1/2″ rope of plumbing’s putty around the drain opening in the sink. Go down the new sink flange into the drain opening as well as press it into location. Positioning a weight, such as your garbage disposal, in addition to the sink flange will certainly help hold the sink flange in place while installing it to the sink. To prevent scratching your sink or the flange, place a towel in between the sink surface area and also the weight.
6. Mount gasket and also flanges.
From under the sink, slide the fiber gasket, backup flange as well as installing flange over the sink flange. Hold these pieces in position.
7. Slip on the mounting as well as snap rings.
Next, slip on the placing ring as well as break ring. Tighten the 3 mounting screws, alternately tightening each screw a couple of turns each time till the placing assembly is uniformly and snugly seated versus the bottom of the sink.
8. Remove the dishwasher ko plug.
If using a dishwashing machine, you will require to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and utilize a screwdriver and hammer to touch it out. Next off, eliminate the loosened ko plug from inside the garbage disposal.
9. Link the electrical.
Hardwired System:.
Turn the garbage disposal over as well as eliminate electric cover plate. Take out cables. Place cable television connector (not included) as well as run electrical cable television with access opening on base of garbage disposal. Tighten wire port. Push cables right into garbage disposal (do not displace cardboard guard) and also change electrical cover plate.
If you have a hardwired device and also you’re aiming to connect a cable, you will need a power cord kit.
Corded Unit:.
For a garbage disposal with a factory-installed cord, just connect in to the electrical outlet under your sink after completing the remainder of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced installing ring till all 3 tabs are secured right into the mounting setting up.
11. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drain pipeline.
Turn the garbage disposal so that the discharge tube is aligned with the drainpipe trap. If the discharge tube is also long, cut off as much of the tube as required. If it is too brief, you can buy an expansion. If you are attaching the garbage disposal to a dishwashing machine, it may be connected via an air gap. Make use of a hose pipe clamp to attach the drain tube to the dishwashing machine inlet.
13. Lock the garbage disposal in position.
Now that everything is set up and also in position, lock the garbage disposal to the sink mounting setting up using the wrench that came with the unit. Place the Quiet Collar Sink Baffle right into the sink opening by pressing it into the sink until it snaps into area.
14. Evaluate the garbage disposal.
Examination for leakages at the sink flange, dishwasher, tail-pipe as well as installing assembly connections. Finally, turn on the electrical breaker to evaluate its operation. Enjoy your brand-new garbage disposal!
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Sun Valley
Garbage Disposal Installation: In Detail in Sun Valley