1. Disconnect the p-trap and the horizontal extension pipeline.
Huge channel-lock pliers or a pipe wrench work well to loosen up the nuts holding the pipes with each other. When both links are free, remove the components. You may intend to clean up the straight drain pipeline to eliminate any possible obstruction. (This is not needed in new construction.).
2. Disconnect the down drain.
Making use of huge channel-lock pliers, disconnect the down drainpipe coming from the sink and the link that affixes it to the p-trap. When both connections are totally free, remove the parts.
3. Unscrew the big nut.
Unscrew the large nut that holds the strainer in position beneath the sink. Remove the strainer body.
4. Pry off the breeze ring as well as wipe the old plumbing’s putty.
Utilizing a flathead screwdriver, loosen the 3 screws on the mounting assembly and pry off the snap ring. Wipe the old plumbing’s putty that borders the edge of the drainpipe opening.
5. Set up the new sink flange.
Location a 1/2″ rope of plumbing professional’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange into the drainpipe opening and press it into location. Putting a weight, such as your garbage disposal, in addition to the sink flange will certainly assist hold the sink flange in position while mounting it to the sink. To stay clear of scratching your sink or the flange, place a towel in between the sink surface as well as the weight.
6. Install gasket and flanges.
From under the sink, slide the fiber gasket, backup flange and placing flange over the sink flange. Hold these pieces in place.
7. Slip on the installing as well as snap rings.
Next, slip on the mounting ring and also break ring. Tighten up the three mounting screws, at the same time tightening up each screw a few turns at a time up until the placing setting up is evenly and tightly seated against all-time low of the sink.
8. Remove the dish washer knockout plug.
If using a dishwasher, you will require to touch out the dishwasher knockout plug. Lay the garbage disposal on its side and use a screwdriver and hammer to touch it out. Next off, eliminate the loosened ko plug from inside the garbage disposal.
9. Link the electrical.
Hardwired Device:.
Turn the garbage disposal over as well as eliminate electric cover plate. Take out cables. Put cable television connector (not consisted of) and also run electric cable television via access opening on base of garbage disposal. Tighten cable adapter. Push wires into garbage disposal (do not displace cardboard guard) and also replace electric cover plate.
If you have a hardwired unit and you’re seeking to affix a cable, you will require a power cable package.
Corded Unit:.
For a garbage disposal with a factory-installed cord, simply connect in to the outlet under your sink after finishing the remainder of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced mounting ring until all 3 tabs are locked into the mounting assembly.
11. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drain pipe.
Turn the garbage disposal to make sure that the discharge tube is aligned with the drainpipe catch. If the discharge tube is as well long, removed as a lot of the tube as required. If it is too brief, you can purchase an expansion. If you are attaching the garbage disposal to a dishwasher, it might be attached through an air space. Make use of a pipe clamp to affix the drain tube to the dish washer inlet.
13. Lock the garbage disposal in place.
Now that everything is mounted and also in position, lock the garbage disposal to the sink mounting setting up utilizing the wrench that featured the system. Place the Quiet Collar Sink Baffle right into the sink opening by pressing it into the sink till it snaps right into location.
14. Test the garbage disposal.
Examination for leaks at the sink flange, dishwasher, tail-pipe as well as placing setting up links. Finally, activate the electric breaker to examine its procedure. Enjoy your brand-new garbage disposal!
Mounting a Replacement Garbage Disposal in Sunland-Tujunga
How to Choose a Garbage Disposal in Sunland-Tujunga