1. Turn off power to the garbage disposal and also disconnect the down trap.
Shut off the electric power at the fuse box or circuit breaker. After that, using adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and insert completion of the wrenchette or screwdriver right into the appropriate side of one mounting lug on the reduced placing ring. Lift the garbage disposal somewhat as well as loosen up the lower mounting ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the placing assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and remove the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw as well as remove wire ports. Detach garbage disposal cords from electrical supply cords. Loosen screws on the electric clamp adapter as well as remove cords from the garbage disposal.
4. Eliminate existing installing equipment if hardware substitute required. Or else avoid to step 12.
To remove the existing mounting hardware, loosen up the 3 installing screws, tear the snap ring off with a screwdriver and remove the old mounting setting up.
5. Remove the old sink flange as well as putty.
Press the old sink flange up via the sink hole. Utilize a screwdriver or putty blade to meticulously scrape all old putty from the edge of the sink hole
. Mount the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Drop the new sink flange right into the drain opening as well as press it into area. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly help hold the sink flange in place while mounting the sink flange to the sink. To prevent scratching your sink or the flange, put a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange as well as placing flange over the sink flange. Hold these pieces in position.
7. Remove the dishwashing machine ko plug.
If making use of a dishwashing machine, you will require to tap out the dish washer ko plug. Lay the garbage disposal on its side and also use a screwdriver and hammer to touch it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
8. Connect the electric.
Hardwired Unit:
Turn the garbage disposal over and remove electric cover plate. Pull out wires. Insert cord port (not included) as well as run electrical wire with accessibility opening on bottom of garbage disposal. Tighten up wire adapter. Press cables right into garbage disposal (do not displace cardboard guard) as well as change electrical cover plate.
If you have a hardwired device and you’re aiming to attach a cord, you will need a power cord package.
Corded Unit:
For a garbage disposal with a factory-installed cord, just connect in to the outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the lower mounting ring till all 3 tabs are locked into the installing assembly. The garbage disposal will now hang by itself.
10. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain catch. If the discharge tube is also long, cut off as high as essential. If it is also brief, you can acquire an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dish washer, it may be attached via an air space. Use a hose pipe clamp to attach the drain hose to the dishwashing machine inlet. Since everything is mounted as well as ready, lock the garbage disposal to the sink placing setting up utilizing the wrenchette that came with the system. For Advancement designs, place the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps right into location.
13. Examine the garbage disposal.
For all designs, you ought to examine for leakages at the sink flange, dishwasher, tail-pipe as well as placing setting up connections. Ultimately, activate the electrical breaker to evaluate its operation.
Installing a New Garbage Disposal in Costa Mesa
Starting a Garbage Disposal Installation Project in Costa Mesa