1. Turn off power to the garbage disposal as well as disconnect the down catch.
Turn off the electric power at the fuse box or breaker. After that, using adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand and also put the end of the wrenchette or screwdriver into the best side of one installing lug on the reduced installing ring. Raise the garbage disposal slightly as well as loosen the lower placing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the mounting setting up.
3. Separate the electrical.
Lay the garbage disposal on its side as well as get rid of the electric cover plate from the bottom. Loosen the green ground screw and also get rid of cable adapters. Disconnect garbage disposal cords from electric supply cords. Loosen screws on the electrical clamp port as well as remove wires from the garbage disposal.
4. Get rid of existing placing hardware if hardware replacement needed. Or else miss to step 12.
To remove the existing installing equipment, loosen the 3 placing screws, pry the breeze ring off with a screwdriver as well as eliminate the old mounting assembly.
5. Eliminate the old sink flange and putty.
Press the old sink flange up via the sink opening. Utilize a screwdriver or putty blade to very carefully scuff all old putty from the side of the sink hole
. Install the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drainpipe opening as well as press it into place. Placing a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in place while placing the sink flange to the sink. To stay clear of scratching your sink or the flange, place a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in place.
7. Remove the dishwashing machine ko plug.
If making use of a dish washer, you will require to tap out the dish washer knockout plug. Lay the garbage disposal on its side and utilize a screwdriver and hammer to touch it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Attach the electric.
Hardwired Unit:
Turn the garbage disposal over and eliminate electrical cover plate. Take out cables. Place cable port (not included) and also run electric cord with access opening on base of garbage disposal. Tighten wire connector. Push cables into garbage disposal (do not displace cardboard shield) as well as change electrical cover plate.
If you have a hardwired unit and you’re wanting to attach a cord, you will certainly need a power cable set.
Corded Device:
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the lower mounting ring up until all three tabs are locked right into the installing assembly. The garbage disposal will now hang by itself.
10. Place the discharge tube.
Insert the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Revolve the garbage disposal so that the discharge tube is lined up with the drain catch. If the discharge tube is also long, removed as high as required. If it is also short, you can acquire an expansion.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dish washer, it may be connected through an air gap. Utilize a hose pipe clamp to affix the drain pipe to the dishwashing machine inlet. Since every little thing is mounted and ready, secure the garbage disposal to the sink mounting assembly making use of the wrenchette that included the unit. For Advancement versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink till it breaks into location.
13. Test the garbage disposal.
For all designs, you should test for leaks at the sink flange, dishwasher, tail-pipe and also placing assembly connections. Finally, activate the electric breaker to evaluate its operation.
Garbage Disposal Installation Benefits in Diamond Bar
Installing a New Garbage Disposal in Diamond Bar