1. Turn off power to the garbage disposal as well as detach the down trap.
Turn off the electrical power at the circuit box or circuit breaker. Then, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand as well as place the end of the wrenchette or screwdriver into the right side of one mounting lug on the lower mounting ring. Lift the garbage disposal somewhat and also loosen up the reduced placing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is free from the mounting setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side and also remove the electric cover plate from all-time low. Loosen the environment-friendly ground screw and also eliminate wire ports. Detach garbage disposal cords from electric supply cables. Loosen screws on the electrical clamp connector as well as get rid of cords from the garbage disposal.
4. Remove existing installing hardware if equipment replacement needed. Or else skip to step 12.
To eliminate the existing installing equipment, loosen the three mounting screws, pry the breeze ring off with a screwdriver as well as get rid of the old placing setting up.
5. Eliminate the old sink flange and putty.
Push the old sink flange up through the sink hole. Use a screwdriver or putty knife to meticulously scuff all old putty from the side of the sink opening
. Set up the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange into the drainpipe opening and also press it into location. Putting a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To prevent damaging your sink or the flange, put a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these items in position.
7. Get rid of the dish washer knockout plug.
If using a dish washer, you will certainly need to tap out the dish washer ko plug. Lay the garbage disposal on its side as well as utilize a screwdriver and also hammer to tap it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired System:
Turn the garbage disposal over as well as get rid of electrical cover plate. Pull out wires. Put wire connector (not consisted of) as well as run electrical wire via access opening on base of garbage disposal. Tighten cord adapter. Push cables right into garbage disposal (do not displace cardboard guard) and also replace electrical cover plate.
If you have a hardwired unit and you’re looking to connect a cord, you will need a power cable kit.
Corded Unit:
For a garbage disposal with a factory-installed cable, just plug in to the outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, turn the reduced mounting ring up until all three tabs are secured right into the placing assembly. The garbage disposal will now hang by itself.
10. Place the discharge tube.
Place the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Rotate the garbage disposal so that the discharge tube is straightened with the drain trap. If the discharge tube is also long, removed as long as necessary. If it is also brief, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwashing machine, it might be linked through an air gap. Use a pipe clamp to affix the drainpipe tube to the dishwashing machine inlet. Since whatever is set up and ready, lock the garbage disposal to the sink mounting setting up utilizing the wrenchette that featured the system. For Evolution versions, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink up until it snaps into location.
13. Check the garbage disposal.
For all models, you ought to check for leaks at the sink flange, dishwashing machine, tail-pipe and mounting setting up connections. Ultimately, switch on the electrical breaker to test its procedure.
How to Choose a Garbage Disposal in Guasti
Garbage Disposal installation for new homes in Guasti