1. Switch off power to the garbage disposal and also separate the down catch.
Switch off the electrical power at the fuse box or breaker. After that, utilizing adjustable pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Assistance the garbage disposal with one hand and also place completion of the wrenchette or screwdriver into the ideal side of one installing lug on the reduced placing ring. Raise the garbage disposal a little and loosen up the reduced placing ring by pushing or pulling the wrenchette or screwdriver to the left up until the garbage disposal is devoid of the installing setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side and eliminate the electric cover plate from all-time low. Loosen the green ground screw as well as eliminate cable adapters. Separate garbage disposal wires from electrical supply cords. Loosen up screws on the electrical clamp connector as well as remove wires from the garbage disposal.
4. Get rid of existing installing equipment if hardware substitute required. Otherwise avoid to step 12.
To get rid of the existing mounting equipment, loosen the three placing screws, tear the breeze ring off with a screwdriver and eliminate the old mounting assembly.
5. Get rid of the old sink flange and putty.
Press the old sink flange up via the sink opening. Make use of a screwdriver or putty blade to thoroughly scuff all old putty from the side of the sink hole
. Install the new sink flange, gasket as well as rings.
Place a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange into the drain opening and press it right into location. Putting a weight, such as the garbage disposal, in addition to the sink flange will certainly help hold the sink flange in position while installing the sink flange to the sink. To stay clear of damaging your sink or the flange, put a towel in between the sink surface area and the weight. From under the sink, slide the fiber gasket, backup flange and also mounting flange over the sink flange. Hold these items in position.
7. Get rid of the dishwashing machine ko plug.
If using a dish washer, you will require to touch out the dishwasher ko plug. Lay the garbage disposal on its side and use a screwdriver and also hammer to touch it out. Next, remove the loosened knockout plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Unit:
Transform the garbage disposal over and also eliminate electric cover plate. Pull out cables. Place cable connector (not consisted of) and run electric cable television with access opening on base of garbage disposal. Tighten cable television connector. Push wires into garbage disposal (do not displace cardboard shield) and also replace electric cover plate.
If you have a hardwired system and you’re looking to attach a cord, you will certainly require a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cord, just connect in to the electrical outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the lower mounting ring until all three tabs are locked into the installing assembly. The garbage disposal will certainly now hang on its own.
10. Place the discharge tube.
Place the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Turn the garbage disposal to ensure that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, cut off as high as required. If it is also brief, you can buy an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dish washer, it might be attached through an air space. Use a hose clamp to connect the drain pipe to the dishwashing machine inlet. Now that everything is installed as well as ready, lock the garbage disposal to the sink installing setting up making use of the wrenchette that featured the unit. For Development versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink up until it breaks right into place.
13. Test the garbage disposal.
For all models, you must test for leaks at the sink flange, dish washer, tail-pipe as well as placing setting up connections. Finally, switch on the electric breaker to evaluate its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Hawaiian Gardens
Starting a Garbage Disposal Installation Project in Hawaiian Gardens