1. Shut off power to the garbage disposal and detach the down trap.
Shut off the electric power at the circuit box or circuit breaker. After that, using flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand as well as place the end of the wrenchette or screwdriver right into the best side of one placing lug on the lower mounting ring. Lift the garbage disposal somewhat and loosen the reduced mounting ring by pressing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the placing assembly.
3. Separate the electric.
Lay the garbage disposal on its side as well as eliminate the electric cover plate from the bottom. Loosen the eco-friendly ground screw and also eliminate cable ports. Separate garbage disposal cords from electrical supply cords. Loosen up screws on the electric clamp adapter and also eliminate wires from the garbage disposal.
4. Eliminate existing placing equipment if hardware substitute needed. Otherwise miss to tip 12.
To eliminate the existing placing equipment, loosen the three placing screws, tear the breeze ring off with a screwdriver as well as remove the old placing assembly.
5. Remove the old sink flange as well as putty.
Push the old sink flange up via the sink opening. Make use of a screwdriver or putty blade to carefully scrape all old putty from the edge of the sink hole
. Mount the brand-new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Drop the new sink flange right into the drain opening and also press it into place. Positioning a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in position while installing the sink flange to the sink. To stay clear of scratching your sink or the flange, put a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in place.
7. Get rid of the dishwasher ko plug.
If using a dishwasher, you will need to tap out the dish washer knockout plug. Lay the garbage disposal on its side and also utilize a screwdriver as well as hammer to tap it out. Next off, get rid of the loose knockout plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired System:
Turn the garbage disposal over as well as remove electric cover plate. Take out cords. Insert cord connector (not included) and also run electric cord with gain access to hole on base of garbage disposal. Tighten cord port. Press cords right into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired device and also you’re looking to connect a cable, you will certainly require a power cable set.
Corded Unit:
For a garbage disposal with a factory-installed cord, merely connect in to the outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the lower placing ring until all 3 tabs are locked into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Insert the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Rotate the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is also long, removed as much as essential. If it is also brief, you can acquire an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwashing machine, it might be attached via an air void. Use a hose pipe clamp to affix the drainpipe pipe to the dishwashing machine inlet. Now that every little thing is installed and also ready, secure the garbage disposal to the sink installing assembly using the wrenchette that came with the device. For Advancement versions, insert the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink up until it breaks into place.
13. Examine the garbage disposal.
For all designs, you must test for leakages at the sink flange, dishwashing machine, tail-pipe as well as mounting setting up links. Lastly, activate the electric breaker to evaluate its procedure.
Everything You Required to Know About Garbage Disposals in La Puente