Installing a Replacement Garbage Disposal in Laguna Hills

1. Turn off power to the garbage disposal and separate the down trap.
Turn off the electrical power at the circuit box or breaker. Then, utilizing adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and also insert the end of the wrenchette or screwdriver right into the ideal side of one mounting lug on the lower placing ring. Lift the garbage disposal somewhat and loosen up the reduced mounting ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the installing setting up.
3. Separate the electric.
Lay the garbage disposal on its side as well as remove the electric cover plate from the bottom. Loosen up the green ground screw and also eliminate cord adapters. Separate garbage disposal cables from electrical supply wires. Loosen screws on the electrical clamp connector and remove cords from the garbage disposal.

4. Get rid of existing mounting hardware if hardware substitute needed. Or else miss to step 12.
To get rid of the existing mounting hardware, loosen the three installing screws, tear the breeze ring off with a screwdriver as well as remove the old installing assembly.

5. Get rid of the old sink flange and also putty.
Press the old sink flange up with the sink opening. Use a screwdriver or putty blade to thoroughly scrape all old putty from the edge of the sink hole
. Set up the brand-new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Go down the brand-new sink flange into the drain opening and press it right into location. Putting a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in position while placing the sink flange to the sink. To prevent scraping your sink or the flange, position a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as placing flange over the sink flange. Hold these pieces in place.

7. Eliminate the dishwashing machine ko plug.
If utilizing a dishwasher, you will certainly require to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also use a screwdriver as well as hammer to tap it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired System:
Turn the garbage disposal over and remove electric cover plate. Take out cables. Put cable television connector (not included) and run electric cable through accessibility opening on base of garbage disposal. Tighten wire adapter. Press wires into garbage disposal (do not displace cardboard guard) and also change electric cover plate.
If you have a hardwired system and you’re seeking to attach a cord, you will require a power cable package.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply connect in to the electrical outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the reduced mounting ring till all 3 tabs are secured right into the placing assembly. The garbage disposal will certainly currently hang by itself.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, then move the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Turn the garbage disposal so that the discharge tube is straightened with the drainpipe catch. If the discharge tube is too long, removed as long as needed. If it is as well brief, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dish washer, it might be connected with an air void. Utilize a hose pipe clamp to attach the drainpipe pipe to the dishwasher inlet. Since every little thing is set up and also in position, lock the garbage disposal to the sink placing setting up utilizing the wrenchette that included the unit. For Development designs, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink till it breaks right into location.

13. Check the garbage disposal.
For all models, you must examine for leaks at the sink flange, dishwasher, tail-pipe and also installing assembly connections. Finally, activate the electrical breaker to evaluate its procedure.
DIY Garbage Disposal Installation in Laguna Hills
What to Think About During Garbage Disposal Installation in Laguna Hills