1. Shut off power to the garbage disposal as well as disconnect the down trap.
Switch off the electric power at the fuse box or breaker. After that, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also insert completion of the wrenchette or screwdriver right into the ideal side of one mounting lug on the lower placing ring. Lift the garbage disposal slightly as well as loosen the reduced mounting ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the installing setting up.
3. Detach the electric.
Lay the garbage disposal on its side and also remove the electric cover plate from all-time low. Loosen up the environment-friendly ground screw and also get rid of cord adapters. Disconnect garbage disposal cords from electrical supply cords. Loosen up screws on the electric clamp connector and eliminate cables from the garbage disposal.
4. Get rid of existing placing hardware if equipment replacement required. Otherwise miss to tip 12.
To eliminate the existing installing hardware, loosen up the 3 installing screws, tear the breeze ring off with a screwdriver and eliminate the old installing setting up.
5. Get rid of the old sink flange as well as putty.
Press the old sink flange up through the sink hole. Use a screwdriver or putty knife to meticulously scuff all old putty from the side of the sink opening
. Install the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening and also press it into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will certainly help hold the sink flange in position while placing the sink flange to the sink. To avoid damaging your sink or the flange, put a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and also placing flange over the sink flange. Hold these pieces in position.
7. Eliminate the dish washer ko plug.
If making use of a dishwasher, you will need to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Unit:
Transform the garbage disposal over and get rid of electrical cover plate. Pull out wires. Place wire adapter (not consisted of) and run electrical wire with gain access to hole on base of garbage disposal. Tighten cable port. Press wires into garbage disposal (do not displace cardboard guard) and replace electric cover plate.
If you have a hardwired unit as well as you’re aiming to connect a cord, you will certainly need a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the reduced installing ring up until all three tabs are secured right into the placing setting up. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Put the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe catch.
Rotate the garbage disposal so that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, removed as high as needed. If it is as well short, you can purchase an expansion.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwashing machine, it might be connected with an air gap. Utilize a hose clamp to attach the drain hose to the dishwashing machine inlet. Since every little thing is installed and also ready, secure the garbage disposal to the sink installing assembly using the wrenchette that came with the device. For Development designs, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink until it breaks right into area.
13. Test the garbage disposal.
For all models, you ought to check for leaks at the sink flange, dish washer, tail-pipe as well as installing assembly links. Ultimately, activate the electric breaker to examine its procedure.
Garbage Disposal Installation: An Environmental and Affordable Option in Sun Valley