1. Shut off power to the garbage disposal and also detach the down trap.
Switch off the electrical power at the circuit box or breaker. After that, making use of adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand as well as put the end of the wrenchette or screwdriver right into the ideal side of one placing lug on the reduced placing ring. Lift the garbage disposal a little as well as loosen the reduced installing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting setting up.
3. Separate the electrical.
Lay the garbage disposal on its side and also remove the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw and remove cable connectors. Detach garbage disposal wires from electrical supply wires. Loosen screws on the electrical clamp adapter as well as get rid of cords from the garbage disposal.
4. Eliminate existing placing hardware if hardware substitute needed. Or else skip to tip 12.
To eliminate the existing placing hardware, loosen up the 3 placing screws, tear the snap ring off with a screwdriver as well as get rid of the old placing setting up.
5. Remove the old sink flange as well as putty.
Press the old sink flange up through the sink opening. Make use of a screwdriver or putty blade to carefully scuff all old putty from the side of the sink hole
. Mount the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drainpipe opening and press it into place. Placing a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in place while placing the sink flange to the sink. To avoid scratching your sink or the flange, place a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, back-up flange as well as installing flange over the sink flange. Hold these items in place.
7. Eliminate the dishwasher knockout plug.
If making use of a dish washer, you will certainly need to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and hammer to touch it out. Next, remove the loosened knockout plug from inside the garbage disposal.
8. Attach the electrical.
Transform the garbage disposal over and eliminate electrical cover plate. Take out cords. Place cord connector (not consisted of) as well as run electrical cable television via accessibility opening on bottom of garbage disposal. Tighten cable adapter. Push wires into garbage disposal (do not displace cardboard shield) and also replace electrical cover plate.
If you have a hardwired unit as well as you’re seeking to attach a cord, you will require a power cable set.
For a garbage disposal with a factory-installed cord, merely connect in to the outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the lower mounting ring up until all 3 tabs are secured into the installing assembly. The garbage disposal will certainly now hang by itself.
10. Insert the discharge tube.
Insert the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Turn the garbage disposal so that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, cut off as long as required. If it is as well brief, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwasher, it might be linked with an air space. Use a hose pipe clamp to connect the drainpipe hose to the dishwasher inlet. Now that every little thing is set up and ready, lock the garbage disposal to the sink installing setting up making use of the wrenchette that came with the device. For Advancement models, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps into location.
13. Test the garbage disposal.
For all designs, you ought to check for leaks at the sink flange, dishwasher, tail-pipe and also placing setting up links. Finally, turn on the electrical breaker to check its operation.
DIY Garbage Disposal Installation in Arcadia
Starting a Garbage Disposal Installation Project in Arcadia