1. Turn off power to the garbage disposal and detach the down trap.
Shut off the electrical power at the fuse box or circuit breaker. Then, making use of adjustable pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and also place the end of the wrenchette or screwdriver into the right side of one installing lug on the lower installing ring. Raise the garbage disposal slightly as well as loosen up the lower installing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is without the placing setting up.
3. Detach the electrical.
Lay the garbage disposal on its side as well as eliminate the electrical cover plate from the bottom. Loosen up the green ground screw as well as eliminate wire adapters. Disconnect garbage disposal cables from electrical supply cables. Loosen up screws on the electrical clamp connector and also get rid of cords from the garbage disposal.
4. Get rid of existing installing equipment if hardware substitute required. Otherwise skip to tip 12.
To get rid of the existing mounting equipment, loosen the 3 mounting screws, pry the snap ring off with a screwdriver and get rid of the old installing setting up.
5. Remove the old sink flange and putty.
Press the old sink flange up with the sink hole. Utilize a screwdriver or putty blade to thoroughly scratch all old putty from the edge of the sink hole
. Install the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Go down the new sink flange into the drain opening as well as press it into place. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in position while mounting the sink flange to the sink. To prevent scraping your sink or the flange, position a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these items in place.
7. Remove the dish washer knockout plug.
If using a dish washer, you will need to touch out the dishwasher ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to touch it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Link the electric.
Hardwired Device:
Transform the garbage disposal over and also eliminate electrical cover plate. Take out cords. Insert cable port (not included) as well as run electrical cable television with accessibility hole on base of garbage disposal. Tighten wire port. Press cords into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired system and you’re looking to attach a cord, you will need a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cable, merely connect in to the electrical outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the lower mounting ring up until all three tabs are locked right into the mounting assembly. The garbage disposal will certainly currently hang on its own.
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then glide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain catch. If the discharge tube is as well long, cut off as long as necessary. If it is as well short, you can buy an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it may be attached with an air gap. Use a pipe clamp to attach the drainpipe pipe to the dish washer inlet. Since everything is set up and also ready, lock the garbage disposal to the sink installing setting up making use of the wrenchette that included the device. For Development designs, place the Quiet Collar ® Sink Baffle right into the sink opening by pushing it right into the sink up until it breaks right into place.
13. Test the garbage disposal.
For all designs, you need to test for leaks at the sink flange, dish washer, tail-pipe and placing setting up links. Ultimately, turn on the electrical breaker to evaluate its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in East Irvine
How to Choose a Garbage Disposal in East Irvine