1. Shut off power to the garbage disposal and also separate the down trap.
Turn off the electric power at the circuit box or breaker. After that, using adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Assistance the garbage disposal with one hand and also place the end of the wrenchette or screwdriver right into the right side of one placing lug on the lower placing ring. Lift the garbage disposal slightly and also loosen up the reduced placing ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is devoid of the mounting setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side as well as eliminate the electrical cover plate from all-time low. Loosen up the eco-friendly ground screw and remove cable connectors. Disconnect garbage disposal cords from electrical supply cables. Loosen screws on the electrical clamp port as well as get rid of cables from the garbage disposal.
4. Eliminate existing mounting hardware if hardware replacement required. Otherwise miss to step 12.
To eliminate the existing installing hardware, loosen the three mounting screws, pry the breeze ring off with a screwdriver as well as eliminate the old installing setting up.
5. Get rid of the old sink flange and putty.
Press the old sink flange up with the sink hole. Use a screwdriver or putty blade to meticulously scuff all old putty from the edge of the sink hole
. Mount the brand-new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drainpipe opening as well as press it right into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in position while installing the sink flange to the sink. To prevent scratching your sink or the flange, place a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and also placing flange over the sink flange. Hold these pieces in position.
7. Get rid of the dishwasher knockout plug.
If using a dishwashing machine, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and hammer to touch it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired Unit:
Transform the garbage disposal over and also get rid of electric cover plate. Pull out wires. Put cable connector (not included) as well as run electric cable television with accessibility opening on bottom of garbage disposal. Tighten up cable television port. Push cables right into garbage disposal (do not displace cardboard shield) as well as change electrical cover plate.
If you have a hardwired device as well as you’re wanting to attach a cord, you will require a power cord package.
Corded Device:
For a garbage disposal with a factory-installed cord, merely connect in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, transform the reduced mounting ring up until all three tabs are secured right into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Put the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe catch.
Rotate the garbage disposal to ensure that the discharge tube is straightened with the drain catch. If the discharge tube is too long, cut off as much as necessary. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwasher, it might be linked with an air space. Use a pipe clamp to affix the drainpipe hose to the dishwashing machine inlet. Since whatever is mounted as well as ready, lock the garbage disposal to the sink mounting assembly using the wrenchette that came with the system. For Development designs, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it right into the sink up until it snaps into place.
13. Check the garbage disposal.
For all designs, you should evaluate for leaks at the sink flange, dishwashing machine, tail-pipe and also mounting setting up connections. Ultimately, activate the electrical breaker to test its procedure.
New Garbage Disposal Installation Guide in Llano