1. Shut off power to the garbage disposal as well as separate the down trap.
Shut off the electrical power at the circuit box or circuit breaker. After that, utilizing flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and place completion of the wrenchette or screwdriver into the appropriate side of one placing lug on the lower installing ring. Lift the garbage disposal a little and also loosen up the lower placing ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting assembly.
3. Separate the electrical.
Lay the garbage disposal on its side and eliminate the electric cover plate from all-time low. Loosen the green ground screw and remove wire connectors. Disconnect garbage disposal cables from electric supply wires. Loosen screws on the electric clamp adapter as well as remove cords from the garbage disposal.
4. Eliminate existing installing equipment if equipment substitute required. Or else avoid to tip 12.
To eliminate the existing installing equipment, loosen up the 3 installing screws, tear the snap ring off with a screwdriver and also get rid of the old placing assembly.
5. Get rid of the old sink flange and putty.
Push the old sink flange up with the sink opening. Utilize a screwdriver or putty blade to very carefully scuff all old putty from the edge of the sink opening
. Install the brand-new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumbing professional’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drainpipe opening as well as press it into location. Placing a weight, such as the garbage disposal, in addition to the sink flange will aid hold the sink flange in position while placing the sink flange to the sink. To avoid damaging your sink or the flange, position a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and also mounting flange over the sink flange. Hold these items in place.
7. Eliminate the dish washer knockout plug.
If using a dish washer, you will require to tap out the dish washer knockout plug. Lay the garbage disposal on its side and also utilize a screwdriver as well as hammer to tap it out. Next off, eliminate the loose ko plug from inside the garbage disposal.
8. Link the electrical.
Hardwired System:
Transform the garbage disposal over and also remove electric cover plate. Take out cables. Insert wire port (not consisted of) and also run electric cord with access hole on base of garbage disposal. Tighten up cord adapter. Push cables right into garbage disposal (do not displace cardboard guard) and replace electric cover plate.
If you have a hardwired unit and you’re wanting to affix a cord, you will need a power cable package.
Corded System:
For a garbage disposal with a factory-installed cable, simply connect in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the reduced installing ring up until all 3 tabs are locked right into the installing setting up. The garbage disposal will certainly currently hang on its own.
10. Place the discharge tube.
Insert the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is also long, removed as high as needed. If it is too short, you can acquire an expansion.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dish washer, it might be attached through an air void. Use a hose pipe clamp to connect the drain pipe to the dishwasher inlet. Now that whatever is mounted and in position, lock the garbage disposal to the sink placing setting up using the wrenchette that featured the device. For Advancement models, place the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink until it breaks into area.
13. Test the garbage disposal.
For all designs, you ought to test for leaks at the sink flange, dish washer, tail-pipe and also placing setting up connections. Finally, activate the electric breaker to check its procedure.
Garbage Disposal installation for brand-new homes in Pacific Palisades
Whatever You Need to Learn About Trash Disposals in Pacific Palisades