1. Switch off power to the garbage disposal and also separate the down catch.
Turn off the electrical power at the circuit box or breaker. After that, making use of flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Support the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the appropriate side of one installing lug on the lower placing ring. Lift the garbage disposal somewhat and loosen the lower installing ring by pushing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the mounting assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and remove the electrical cover plate from all-time low. Loosen up the environment-friendly ground screw and eliminate cable adapters. Separate garbage disposal wires from electrical supply wires. Loosen screws on the electrical clamp adapter as well as remove cables from the garbage disposal.
4. Eliminate existing mounting equipment if hardware substitute needed. Or else avoid to tip 12.
To remove the existing mounting hardware, loosen the 3 placing screws, tear the breeze ring off with a screwdriver as well as remove the old placing assembly.
5. Get rid of the old sink flange and also putty.
Push the old sink flange up through the sink hole. Utilize a screwdriver or putty blade to thoroughly scrape all old putty from the edge of the sink hole
. Mount the brand-new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the new sink flange into the drainpipe opening as well as press it into place. Placing a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in position while mounting the sink flange to the sink. To avoid scraping your sink or the flange, position a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these items in place.
7. Remove the dishwasher ko plug.
If using a dishwasher, you will need to tap out the dishwasher knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and hammer to tap it out. Next off, get rid of the loose knockout plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired Unit:
Transform the garbage disposal over and also eliminate electric cover plate. Pull out cables. Place cable connector (not included) as well as run electrical cord with access opening on base of garbage disposal. Tighten up cable connector. Press cables right into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired unit and also you’re wanting to affix a cable, you will require a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cord, just connect in to the outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, turn the reduced placing ring until all three tabs are secured right into the installing assembly. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, then move the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe catch.
Revolve the garbage disposal to make sure that the discharge tube is lined up with the drain catch. If the discharge tube is also long, removed as long as needed. If it is too brief, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it may be connected through an air gap. Utilize a pipe clamp to attach the drainpipe pipe to the dishwashing machine inlet. Since everything is mounted as well as in position, lock the garbage disposal to the sink placing assembly making use of the wrenchette that came with the device. For Development versions, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink up until it breaks into area.
13. Examine the garbage disposal.
For all models, you need to evaluate for leaks at the sink flange, dishwashing machine, tail-pipe as well as mounting setting up links. Finally, activate the electric breaker to check its procedure.
New Garbage Disposal Installation Guide in Santa Monica
Whatever You Required to Find Out About Waste Disposals in Santa Monica