1. Turn off power to the garbage disposal and also detach the down catch.
Turn off the electric power at the circuit box or circuit breaker. After that, utilizing adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand as well as put completion of the wrenchette or screwdriver right into the right side of one placing lug on the reduced installing ring. Lift the garbage disposal a little as well as loosen the reduced mounting ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is free from the placing assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen the eco-friendly ground screw and also remove cord ports. Disconnect garbage disposal cords from electrical supply wires. Loosen up screws on the electric clamp connector as well as remove wires from the garbage disposal.
4. Remove existing placing hardware if equipment substitute needed. Otherwise avoid to tip 12.
To remove the existing placing equipment, loosen the 3 placing screws, pry the breeze ring off with a screwdriver and get rid of the old placing setting up.
5. Remove the old sink flange and putty.
Push the old sink flange up via the sink opening. Utilize a screwdriver or putty blade to very carefully scratch all old putty from the side of the sink hole
. Set up the new sink flange, gasket and rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drain opening and also press it right into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will assist hold the sink flange in place while placing the sink flange to the sink. To avoid scraping your sink or the flange, position a towel in between the sink surface area as well as the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these pieces in place.
7. Eliminate the dish washer knockout plug.
If making use of a dishwasher, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver and hammer to touch it out. Next off, eliminate the loose ko plug from inside the garbage disposal.
8. Attach the electric.
Hardwired System:
Turn the garbage disposal over and remove electric cover plate. Take out cords. Insert wire adapter (not included) and run electric wire via gain access to opening on base of garbage disposal. Tighten cable port. Push cables into garbage disposal (do not displace cardboard guard) and also replace electrical cover plate.
If you have a hardwired unit and also you’re seeking to attach a cable, you will need a power cable package.
Corded Unit:
For a garbage disposal with a factory-installed cord, just plug in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the reduced installing ring till all three tabs are secured into the placing setting up. The garbage disposal will certainly now hang by itself.
10. Place the discharge tube.
Insert the discharge tube into the discharge coupler, then slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is as well long, cut off as long as needed. If it is too short, you can acquire an extension.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwasher, it may be linked via an air void. Make use of a pipe clamp to affix the drain hose to the dishwasher inlet. Since every little thing is installed and also ready, lock the garbage disposal to the sink placing setting up using the wrenchette that featured the unit. For Development models, insert the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink till it breaks into place.
13. Test the garbage disposal.
For all designs, you must evaluate for leakages at the sink flange, dishwashing machine, tail-pipe and also mounting assembly links. Lastly, activate the electrical breaker to check its procedure.
How to Install a Garbage Disposal in South Wilmington