1. Turn off power to the garbage disposal and separate the down trap.
Switch off the electrical power at the circuit box or breaker. After that, making use of adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Assistance the garbage disposal with one hand and place the end of the wrenchette or screwdriver into the appropriate side of one mounting lug on the reduced mounting ring. Lift the garbage disposal a little and also loosen the reduced mounting ring by pushing or drawing the wrenchette or screwdriver to the left till the garbage disposal is without the mounting assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and also remove the electric cover plate from all-time low. Loosen up the environment-friendly ground screw and also get rid of wire ports. Disconnect garbage disposal cords from electrical supply wires. Loosen up screws on the electrical clamp port as well as eliminate cords from the garbage disposal.
4. Remove existing placing hardware if hardware replacement required. Otherwise avoid to tip 12.
To eliminate the existing placing hardware, loosen up the 3 mounting screws, pry the breeze ring off with a screwdriver and also remove the old mounting assembly.
5. Remove the old sink flange and putty.
Push the old sink flange up with the sink opening. Utilize a screwdriver or putty knife to very carefully scratch all old putty from the side of the sink opening
. Mount the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drain opening as well as press it into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in place while installing the sink flange to the sink. To stay clear of scratching your sink or the flange, put a towel between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange as well as installing flange over the sink flange. Hold these items in place.
7. Eliminate the dishwasher knockout plug.
If making use of a dishwasher, you will certainly need to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver and hammer to tap it out. Next, eliminate the loosened knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired System:
Transform the garbage disposal over and eliminate electrical cover plate. Pull out cables. Put cable adapter (not included) as well as run electrical wire via gain access to opening on base of garbage disposal. Tighten wire port. Push cords into garbage disposal (do not displace cardboard guard) and also change electric cover plate.
If you have a hardwired unit and also you’re wanting to attach a cord, you will certainly need a power cord package.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply plug in to the outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower placing ring up until all three tabs are locked right into the installing assembly. The garbage disposal will certainly currently hang by itself.
10. Insert the discharge tube.
Place the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube and setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe trap.
Turn the garbage disposal so that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, cut off as much as essential. If it is too short, you can purchase an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dish washer, it might be attached with an air gap. Use a pipe clamp to affix the drain hose to the dishwasher inlet. Since every little thing is mounted and also in position, secure the garbage disposal to the sink installing assembly utilizing the wrenchette that included the system. For Development designs, put the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink till it snaps right into area.
13. Examine the garbage disposal.
For all models, you must evaluate for leakages at the sink flange, dishwasher, tail-pipe as well as installing setting up connections. Ultimately, switch on the electric breaker to test its operation.
How to Choose a Garbage Disposal in Temple City