1. Turn off power to the garbage disposal as well as disconnect the down catch.
Switch off the electric power at the circuit box or circuit breaker. Then, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and place the end of the wrenchette or screwdriver into the right side of one mounting lug on the reduced placing ring. Raise the garbage disposal a little and loosen the reduced installing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is free from the placing setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side as well as get rid of the electrical cover plate from the bottom. Loosen up the green ground screw as well as remove cable adapters. Separate garbage disposal cords from electrical supply wires. Loosen up screws on the electrical clamp port and also eliminate cords from the garbage disposal.
4. Get rid of existing mounting hardware if hardware substitute required. Otherwise miss to step 12.
To eliminate the existing placing hardware, loosen the 3 installing screws, tear the breeze ring off with a screwdriver and get rid of the old placing assembly.
5. Eliminate the old sink flange and also putty.
Press the old sink flange up with the sink hole. Make use of a screwdriver or putty knife to very carefully scratch all old putty from the side of the sink hole
. Mount the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drainpipe opening and also press it right into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly aid hold the sink flange in place while installing the sink flange to the sink. To stay clear of damaging your sink or the flange, position a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as installing flange over the sink flange. Hold these items in place.
7. Get rid of the dishwasher knockout plug.
If making use of a dish washer, you will need to tap out the dishwasher ko plug. Lay the garbage disposal on its side as well as make use of a screwdriver and hammer to touch it out. Next, get rid of the loose ko plug from inside the garbage disposal.
8. Link the electrical.
Hardwired Unit:
Turn the garbage disposal over and remove electric cover plate. Pull out cords. Insert cord connector (not included) and also run electric wire through access opening on base of garbage disposal. Tighten cable television adapter. Push cords right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired system and also you’re wanting to affix a cord, you will require a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cord, simply connect in to the outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower placing ring till all 3 tabs are secured into the placing assembly. The garbage disposal will currently hang on its own.
10. Place the discharge tube.
Put the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe trap.
Revolve the garbage disposal to ensure that the discharge tube is aligned with the drain trap. If the discharge tube is also long, cut off as high as required. If it is too brief, you can buy an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dish washer, it may be linked with an air void. Use a pipe clamp to affix the drain pipe to the dishwasher inlet. Since whatever is set up as well as in position, secure the garbage disposal to the sink mounting assembly making use of the wrenchette that featured the unit. For Advancement versions, put the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink up until it snaps right into area.
13. Examine the garbage disposal.
For all models, you should examine for leakages at the sink flange, dishwasher, tail-pipe and mounting setting up connections. Lastly, turn on the electrical breaker to evaluate its operation.
How to Install a Garbage Disposal in Westminster
New Garbage Disposal Installation Guide in Westminster