1. Turn off power to the garbage disposal and disconnect the down catch.
Switch off the electrical power at the circuit box or circuit breaker. After that, using flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Assistance the garbage disposal with one hand as well as put completion of the wrenchette or screwdriver into the appropriate side of one installing lug on the lower installing ring. Raise the garbage disposal slightly and loosen the reduced placing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the mounting setting up.
3. Detach the electrical.
Lay the garbage disposal on its side and also eliminate the electric cover plate from all-time low. Loosen up the environment-friendly ground screw as well as remove wire ports. Separate garbage disposal cables from electric supply cables. Loosen up screws on the electric clamp port and also remove wires from the garbage disposal.
4. Remove existing installing equipment if hardware substitute required. Otherwise skip to tip 12.
To eliminate the existing installing equipment, loosen up the three placing screws, tear the snap ring off with a screwdriver as well as get rid of the old placing assembly.
5. Remove the old sink flange as well as putty.
Push the old sink flange up through the sink opening. Make use of a screwdriver or putty knife to very carefully scrape all old putty from the side of the sink opening
. Mount the brand-new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drainpipe opening and press it right into place. Placing a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in position while mounting the sink flange to the sink. To avoid scraping your sink or the flange, put a towel between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange as well as mounting flange over the sink flange. Hold these items in place.
7. Eliminate the dishwasher knockout plug.
If utilizing a dish washer, you will certainly need to touch out the dish washer knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to tap it out. Next, remove the loosened ko plug from inside the garbage disposal.
8. Link the electric.
Hardwired Unit:
Transform the garbage disposal over and also remove electric cover plate. Pull out wires. Insert cord adapter (not included) and run electrical cable television via accessibility hole on bottom of garbage disposal. Tighten cable connector. Push cables into garbage disposal (do not displace cardboard guard) and also change electric cover plate.
If you have a hardwired device and also you’re aiming to attach a cable, you will certainly need a power cable package.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply connect in to the outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in position, turn the reduced mounting ring until all three tabs are secured right into the installing assembly. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe catch.
Revolve the garbage disposal to ensure that the discharge tube is aligned with the drain catch. If the discharge tube is too long, removed as much as needed. If it is too short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwasher, it may be attached with an air space. Utilize a pipe clamp to connect the drain hose pipe to the dishwasher inlet. Since whatever is set up as well as in position, secure the garbage disposal to the sink placing assembly making use of the wrenchette that came with the device. For Advancement designs, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it right into the sink until it snaps into place.
13. Evaluate the garbage disposal.
For all versions, you should evaluate for leaks at the sink flange, dishwashing machine, tail-pipe as well as installing assembly connections. Ultimately, activate the electric breaker to check its operation.
New Garbage Disposal Installation Guide in Culver City
DIY Garbage Disposal Installation in Culver City