1. Shut off power to the garbage disposal as well as separate the down catch.
Switch off the electric power at the circuit box or circuit breaker. Then, using adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Assistance the garbage disposal with one hand and also insert completion of the wrenchette or screwdriver into the ideal side of one placing lug on the reduced mounting ring. Raise the garbage disposal a little and loosen the reduced installing ring by pressing or drawing the wrenchette or screwdriver to the left till the garbage disposal is devoid of the installing setting up.
3. Separate the electric.
Lay the garbage disposal on its side and also eliminate the electric cover plate from all-time low. Loosen the eco-friendly ground screw as well as eliminate cable connectors. Detach garbage disposal cords from electric supply wires. Loosen screws on the electrical clamp adapter and also get rid of cables from the garbage disposal.
4. Remove existing mounting equipment if equipment substitute required. Or else avoid to tip 12.
To eliminate the existing placing hardware, loosen the three placing screws, pry the breeze ring off with a screwdriver as well as get rid of the old installing assembly.
5. Get rid of the old sink flange and also putty.
Press the old sink flange up with the sink opening. Utilize a screwdriver or putty blade to thoroughly scuff all old putty from the edge of the sink opening
. Mount the new sink flange, gasket as well as rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Putting a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in position while placing the sink flange to the sink. To prevent scratching your sink or the flange, position a towel in between the sink surface area and also the weight. From under the sink, slide the fiber gasket, backup flange and also mounting flange over the sink flange. Hold these items in place.
7. Eliminate the dishwashing machine knockout plug.
If using a dish washer, you will certainly require to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to touch it out. Next, get rid of the loose ko plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired System:
Transform the garbage disposal over and remove electrical cover plate. Pull out cables. Put wire adapter (not included) and run electric wire through gain access to hole on bottom of garbage disposal. Tighten up cable adapter. Push cords into garbage disposal (do not displace cardboard guard) and also replace electric cover plate.
If you have a hardwired unit and also you’re wanting to attach a cord, you will certainly require a power cord package.
Corded Unit:
For a garbage disposal with a factory-installed cord, just plug in to the electrical outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower mounting ring until all 3 tabs are secured into the placing assembly. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Rotate the garbage disposal to make sure that the discharge tube is straightened with the drainpipe trap. If the discharge tube is too long, cut off as high as essential. If it is as well brief, you can acquire an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwasher, it may be connected with an air void. Make use of a pipe clamp to affix the drain pipe to the dishwashing machine inlet. Since whatever is mounted as well as in position, secure the garbage disposal to the sink placing setting up utilizing the wrenchette that featured the system. For Advancement designs, put the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink until it snaps right into area.
13. Check the garbage disposal.
For all versions, you should evaluate for leakages at the sink flange, dish washer, tail-pipe and also placing assembly links. Lastly, turn on the electrical breaker to evaluate its procedure.
How to Choose a Garbage Disposal in Garden Grove
DIY Garbage Disposal Installation in Garden Grove