1. Turn off power to the garbage disposal and detach the down trap.
Switch off the electric power at the circuit box or circuit breaker. After that, making use of flexible pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand and also place the end of the wrenchette or screwdriver right into the appropriate side of one mounting lug on the reduced placing ring. Lift the garbage disposal somewhat and also loosen the lower placing ring by pressing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the installing assembly.
3. Detach the electrical.
Lay the garbage disposal on its side as well as get rid of the electrical cover plate from the bottom. Loosen the green ground screw and get rid of wire ports. Disconnect garbage disposal cables from electrical supply cables. Loosen up screws on the electrical clamp adapter as well as eliminate wires from the garbage disposal.
4. Get rid of existing installing hardware if hardware substitute required. Or else avoid to step 12.
To eliminate the existing mounting hardware, loosen up the three mounting screws, tear the breeze ring off with a screwdriver and remove the old installing setting up.
5. Eliminate the old sink flange as well as putty.
Press the old sink flange up through the sink opening. Use a screwdriver or putty blade to very carefully scratch all old putty from the side of the sink hole
. Set up the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the new sink flange into the drain opening and also press it into area. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in position while placing the sink flange to the sink. To stay clear of scratching your sink or the flange, place a towel between the sink surface area and also the weight. From under the sink, slide the fiber gasket, backup flange and also mounting flange over the sink flange. Hold these pieces in place.
7. Remove the dish washer ko plug.
If utilizing a dishwashing machine, you will certainly need to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver and also hammer to touch it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Link the electrical.
Hardwired System:
Turn the garbage disposal over and get rid of electric cover plate. Take out wires. Insert wire port (not consisted of) as well as run electric cable with accessibility opening on bottom of garbage disposal. Tighten cable connector. Press wires into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired device and also you’re seeking to connect a cable, you will need a power cable kit.
Corded Device:
For a garbage disposal with a factory-installed cord, merely connect in to the electrical outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced mounting ring till all three tabs are locked right into the mounting assembly. The garbage disposal will certainly currently hang by itself.
10. Insert the discharge tube.
Put the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Revolve the garbage disposal so that the discharge tube is lined up with the drain trap. If the discharge tube is as well long, cut off as long as required. If it is as well brief, you can buy an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dish washer, it may be linked with an air void. Utilize a hose pipe clamp to affix the drain pipe to the dishwasher inlet. Now that every little thing is set up as well as ready, secure the garbage disposal to the sink mounting setting up utilizing the wrenchette that included the unit. For Advancement designs, place the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink till it breaks right into area.
13. Check the garbage disposal.
For all models, you need to evaluate for leaks at the sink flange, dishwasher, tail-pipe and placing setting up connections. Lastly, activate the electrical breaker to evaluate its procedure.
How to Install a Garbage Disposal in Maywood
Installing a New Garbage Disposal in Maywood