Mounting a Replacement Garbage Disposal in Newhall

1. Switch off power to the garbage disposal and separate the down trap.
Turn off the electric power at the circuit box or circuit breaker. Then, using adjustable pliers, separate the drainpipe top from the garbage disposal waste discharge tube.

2. Free the garbage disposal from the installing setting up.
Support the garbage disposal with one hand and place the end of the wrenchette or screwdriver right into the right side of one installing lug on the reduced mounting ring. Lift the garbage disposal slightly and loosen up the lower placing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the mounting assembly.
3. Disconnect the electrical.
Lay the garbage disposal on its side and get rid of the electrical cover plate from all-time low. Loosen up the environment-friendly ground screw and remove cord connectors. Detach garbage disposal cords from electrical supply cords. Loosen up screws on the electrical clamp port and also remove wires from the garbage disposal.

4. Eliminate existing installing equipment if equipment replacement required. Or else avoid to step 12.
To eliminate the existing mounting hardware, loosen the 3 installing screws, tear the breeze ring off with a screwdriver and also get rid of the old placing assembly.

5. Eliminate the old sink flange and also putty.
Press the old sink flange up via the sink opening. Use a screwdriver or putty blade to carefully scrape all old putty from the side of the sink hole
. Set up the new sink flange, gasket as well as rings.
Place a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange right into the drainpipe opening and press it right into location. Placing a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in position while installing the sink flange to the sink. To avoid scratching your sink or the flange, position a towel in between the sink surface area and the weight. From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in position.

7. Eliminate the dishwashing machine knockout plug.
If using a dish washer, you will need to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and utilize a screwdriver as well as hammer to tap it out. Next off, remove the loose knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Unit:
Turn the garbage disposal over as well as eliminate electrical cover plate. Take out cords. Place cable adapter (not consisted of) and run electric cord with access hole on base of garbage disposal. Tighten up cord adapter. Push cords into garbage disposal (do not displace cardboard shield) and also change electrical cover plate.
If you have a hardwired device and also you’re aiming to affix a cable, you will require a power cord set.
Corded Device:
For a garbage disposal with a factory-installed cord, just connect in to the electrical outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower installing ring till all 3 tabs are locked into the installing assembly. The garbage disposal will now hang on its own.
10. Put the discharge tube.
Place the discharge tube into the discharge coupler, then move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain trap.
Revolve the garbage disposal so that the discharge tube is aligned with the drainpipe catch. If the discharge tube is as well long, removed as long as necessary. If it is also brief, you can buy an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it may be attached with an air void. Utilize a hose pipe clamp to affix the drainpipe hose pipe to the dish washer inlet. Since everything is mounted as well as ready, lock the garbage disposal to the sink placing setting up utilizing the wrenchette that featured the unit. For Evolution models, put the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink up until it breaks into location.

13. Evaluate the garbage disposal.
For all designs, you must test for leakages at the sink flange, dish washer, tail-pipe and placing assembly links. Finally, turn on the electrical breaker to evaluate its procedure.
Garbage Disposal Installation: In Detail in Newhall
Starting a Garbage Disposal Installation Project in Newhall