1. Switch off power to the garbage disposal as well as separate the down catch.
Shut off the electrical power at the circuit box or circuit breaker. Then, making use of adjustable pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Support the garbage disposal with one hand and also place the end of the wrenchette or screwdriver into the ideal side of one mounting lug on the lower installing ring. Raise the garbage disposal slightly and also loosen up the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the placing setting up.
3. Disconnect the electric.
Lay the garbage disposal on its side and also eliminate the electrical cover plate from all-time low. Loosen the eco-friendly ground screw and remove cord adapters. Separate garbage disposal cables from electrical supply cables. Loosen up screws on the electric clamp connector and remove cables from the garbage disposal.
4. Eliminate existing installing hardware if hardware substitute needed. Otherwise miss to tip 12.
To eliminate the existing installing hardware, loosen up the three placing screws, tear the snap ring off with a screwdriver and get rid of the old placing setting up.
5. Eliminate the old sink flange as well as putty.
Press the old sink flange up via the sink hole. Utilize a screwdriver or putty knife to very carefully scuff all old putty from the edge of the sink hole
. Set up the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening and also press it into place. Putting a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in position while placing the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these pieces in position.
7. Get rid of the dishwasher knockout plug.
If utilizing a dishwasher, you will need to touch out the dishwasher knockout plug. Lay the garbage disposal on its side and also utilize a screwdriver as well as hammer to touch it out. Next off, get rid of the loosened knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Device:
Transform the garbage disposal over and eliminate electric cover plate. Pull out cords. Put wire adapter (not included) and run electric wire through gain access to opening on base of garbage disposal. Tighten cord adapter. Press wires right into garbage disposal (do not displace cardboard shield) and also change electrical cover plate.
If you have a hardwired unit and also you’re seeking to connect a cord, you will need a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower placing ring until all 3 tabs are locked right into the placing assembly. The garbage disposal will certainly now hang by itself.
10. Insert the discharge tube.
Place the discharge tube right into the discharge coupler, after that glide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Revolve the garbage disposal to ensure that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, removed as long as needed. If it is as well brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwasher, it might be connected through an air space. Utilize a hose clamp to connect the drainpipe tube to the dishwasher inlet. Since everything is set up and also in position, secure the garbage disposal to the sink placing assembly making use of the wrenchette that featured the system. For Development models, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink up until it breaks right into location.
13. Examine the garbage disposal.
For all designs, you must check for leakages at the sink flange, dishwashing machine, tail-pipe and also placing setting up links. Ultimately, turn on the electric breaker to test its procedure.
Starting a Garbage Disposal Installation Project in Phelan
What to Think About During Garbage Disposal Installation in Phelan