1. Switch off power to the garbage disposal and detach the down catch.
Switch off the electrical power at the circuit box or breaker. Then, utilizing adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Assistance the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the appropriate side of one mounting lug on the lower mounting ring. Lift the garbage disposal a little as well as loosen up the lower mounting ring by pressing or drawing the wrenchette or screwdriver to the left till the garbage disposal is devoid of the mounting assembly.
3. Detach the electric.
Lay the garbage disposal on its side and get rid of the electrical cover plate from all-time low. Loosen the eco-friendly ground screw and eliminate wire adapters. Disconnect garbage disposal cables from electric supply cables. Loosen up screws on the electric clamp port and also get rid of cords from the garbage disposal.
4. Eliminate existing placing equipment if hardware replacement needed. Or else miss to step 12.
To eliminate the existing installing hardware, loosen the 3 installing screws, tear the snap ring off with a screwdriver and get rid of the old placing setting up.
5. Eliminate the old sink flange and putty.
Push the old sink flange up via the sink opening. Make use of a screwdriver or putty blade to meticulously scuff all old putty from the edge of the sink hole
. Install the new sink flange, gasket and also rings.
Location a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drainpipe opening and press it into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To prevent scraping your sink or the flange, put a towel between the sink surface area and the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these pieces in place.
7. Remove the dishwasher ko plug.
If utilizing a dishwashing machine, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and make use of a screwdriver and also hammer to touch it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
8. Attach the electrical.
Hardwired Unit:
Turn the garbage disposal over and also get rid of electric cover plate. Take out cords. Put cable adapter (not included) and also run electric cable via accessibility opening on base of garbage disposal. Tighten cord adapter. Push cables into garbage disposal (do not displace cardboard guard) and also replace electrical cover plate.
If you have a hardwired system and also you’re looking to affix a cable, you will certainly require a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cable, just connect in to the outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced placing ring till all 3 tabs are secured right into the mounting assembly. The garbage disposal will now hang on its own.
10. Put the discharge tube.
Insert the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube as well as placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Turn the garbage disposal so that the discharge tube is aligned with the drain trap. If the discharge tube is also long, removed as high as needed. If it is as well brief, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it may be linked with an air void. Utilize a tube clamp to affix the drainpipe pipe to the dishwasher inlet. Now that everything is mounted as well as in position, lock the garbage disposal to the sink placing setting up utilizing the wrenchette that featured the system. For Advancement versions, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it right into the sink until it snaps into place.
13. Check the garbage disposal.
For all versions, you must examine for leakages at the sink flange, dish washer, tail-pipe and also placing setting up connections. Lastly, switch on the electric breaker to test its operation.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Sunland-Tujunga
Installing a New Garbage Disposal in Sunland-Tujunga