1. Turn off power to the garbage disposal and disconnect the down trap.
Turn off the electrical power at the fuse box or breaker. After that, using flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand and insert the end of the wrenchette or screwdriver into the ideal side of one mounting lug on the lower mounting ring. Raise the garbage disposal slightly as well as loosen the reduced installing ring by pressing or drawing the wrenchette or screwdriver to the left until the garbage disposal is without the mounting assembly.
3. Separate the electric.
Lay the garbage disposal on its side and remove the electric cover plate from all-time low. Loosen up the environment-friendly ground screw and get rid of cord ports. Detach garbage disposal wires from electrical supply cables. Loosen screws on the electrical clamp adapter and also get rid of cables from the garbage disposal.
4. Get rid of existing placing equipment if hardware replacement required. Otherwise avoid to tip 12.
To remove the existing mounting equipment, loosen up the three installing screws, tear the snap ring off with a screwdriver and eliminate the old mounting assembly.
5. Eliminate the old sink flange and putty.
Press the old sink flange up with the sink hole. Make use of a screwdriver or putty blade to meticulously scratch all old putty from the edge of the sink opening
. Install the brand-new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the new sink flange into the drain opening as well as press it into location. Positioning a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To prevent scratching your sink or the flange, put a towel between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange and placing flange over the sink flange. Hold these pieces in position.
7. Remove the dishwashing machine knockout plug.
If using a dishwashing machine, you will certainly need to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side as well as use a screwdriver and also hammer to touch it out. Next off, get rid of the loose knockout plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired System:
Turn the garbage disposal over as well as get rid of electrical cover plate. Pull out cords. Place wire connector (not included) and run electric cable through accessibility hole on bottom of garbage disposal. Tighten cord port. Press wires right into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired system and you’re aiming to connect a cable, you will need a power cable set.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply plug in to the outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the reduced placing ring until all three tabs are secured right into the placing assembly. The garbage disposal will certainly currently hang by itself.
10. Place the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe catch.
Revolve the garbage disposal to make sure that the discharge tube is straightened with the drain trap. If the discharge tube is as well long, cut off as high as essential. If it is also brief, you can acquire an expansion.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwasher, it might be attached via an air space. Use a pipe clamp to affix the drain tube to the dishwashing machine inlet. Now that everything is set up as well as in position, lock the garbage disposal to the sink placing assembly using the wrenchette that came with the device. For Advancement models, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps into location.
13. Examine the garbage disposal.
For all designs, you must test for leaks at the sink flange, dishwasher, tail-pipe as well as placing assembly connections. Ultimately, activate the electrical breaker to examine its operation.
What to Look For When Choosing a Garbage Disposal Installation Business in Sunland
How to Install a Garbage Disposal in Sunland