1. Shut off power to the garbage disposal and also detach the down trap.
Shut off the electric power at the circuit box or breaker. After that, making use of flexible pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Assistance the garbage disposal with one hand and also put the end of the wrenchette or screwdriver right into the appropriate side of one placing lug on the lower mounting ring. Raise the garbage disposal slightly as well as loosen the lower installing ring by pushing or drawing the wrenchette or screwdriver to the left till the garbage disposal is devoid of the placing setting up.
3. Detach the electrical.
Lay the garbage disposal on its side as well as remove the electrical cover plate from all-time low. Loosen the environment-friendly ground screw and also eliminate wire adapters. Disconnect garbage disposal cables from electrical supply cables. Loosen up screws on the electrical clamp connector as well as remove wires from the garbage disposal.
4. Eliminate existing mounting hardware if equipment replacement required. Otherwise avoid to step 12.
To get rid of the existing installing hardware, loosen up the 3 installing screws, tear the snap ring off with a screwdriver and get rid of the old mounting assembly.
5. Remove the old sink flange and also putty.
Press the old sink flange up with the sink hole. Use a screwdriver or putty blade to meticulously scratch all old putty from the edge of the sink opening
. Mount the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Go down the brand-new sink flange into the drainpipe opening as well as press it into area. Placing a weight, such as the garbage disposal, in addition to the sink flange will aid hold the sink flange in position while installing the sink flange to the sink. To avoid scraping your sink or the flange, place a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange and also installing flange over the sink flange. Hold these pieces in place.
7. Get rid of the dishwasher ko plug.
If making use of a dish washer, you will certainly need to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side as well as utilize a screwdriver and hammer to touch it out. Next, eliminate the loosened ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Turn the garbage disposal over as well as remove electrical cover plate. Pull out cords. Put cable connector (not included) and run electrical cord via access opening on base of garbage disposal. Tighten cable television port. Press cables right into garbage disposal (do not displace cardboard shield) and change electrical cover plate.
If you have a hardwired system and you’re aiming to connect a cable, you will certainly need a power cable kit.
Corded System:
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower mounting ring till all 3 tabs are secured right into the installing assembly. The garbage disposal will certainly currently hang on its own.
10. Put the discharge tube.
Insert the discharge tube into the discharge coupler, then glide the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain trap.
Rotate the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is too long, cut off as long as essential. If it is also brief, you can buy an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwasher, it might be connected through an air space. Utilize a pipe clamp to connect the drain hose to the dishwasher inlet. Since every little thing is mounted and also ready, lock the garbage disposal to the sink installing setting up utilizing the wrenchette that came with the system. For Development designs, put the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink till it snaps into place.
13. Check the garbage disposal.
For all versions, you should examine for leaks at the sink flange, dish washer, tail-pipe as well as mounting assembly connections. Finally, activate the electrical breaker to examine its operation.
DIY Garbage Disposal Installation in Altadena
Garbage Disposal Installation Benefits in Altadena