1. Turn off power to the garbage disposal and also disconnect the down catch.
Switch off the electrical power at the circuit box or circuit breaker. After that, utilizing flexible pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also insert the end of the wrenchette or screwdriver right into the appropriate side of one placing lug on the reduced installing ring. Raise the garbage disposal a little and loosen up the lower placing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the installing assembly.
3. Disconnect the electric.
Lay the garbage disposal on its side and eliminate the electrical cover plate from the bottom. Loosen up the environment-friendly ground screw and eliminate cable ports. Disconnect garbage disposal wires from electric supply cables. Loosen up screws on the electric clamp port and eliminate cords from the garbage disposal.
4. Remove existing installing equipment if hardware substitute required. Or else skip to step 12.
To eliminate the existing mounting hardware, loosen the three mounting screws, tear the snap ring off with a screwdriver and eliminate the old placing setting up.
5. Get rid of the old sink flange and putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty blade to meticulously scuff all old putty from the side of the sink hole
. Install the new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drainpipe opening in the sink. Go down the brand-new sink flange into the drain opening as well as press it into location. Positioning a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To prevent scraping your sink or the flange, position a towel between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange as well as placing flange over the sink flange. Hold these pieces in place.
7. Remove the dish washer ko plug.
If utilizing a dishwasher, you will certainly need to tap out the dishwashing machine knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to touch it out. Next, remove the loose knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Device:
Turn the garbage disposal over and eliminate electrical cover plate. Pull out cables. Place cable port (not consisted of) as well as run electrical wire via access hole on base of garbage disposal. Tighten cable connector. Press wires right into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired system as well as you’re looking to affix a cable, you will need a power cable kit.
Corded Unit:
For a garbage disposal with a factory-installed cord, simply plug in to the electrical outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the lower mounting ring up until all three tabs are locked into the mounting setting up. The garbage disposal will certainly now hang by itself.
10. Insert the discharge tube.
Place the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Turn the garbage disposal so that the discharge tube is straightened with the drain trap. If the discharge tube is as well long, removed as high as needed. If it is also short, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it might be attached with an air space. Use a tube clamp to attach the drain hose pipe to the dishwasher inlet. Since whatever is set up as well as in position, lock the garbage disposal to the sink installing setting up making use of the wrenchette that featured the device. For Advancement versions, place the Quiet Collar ® Sink Baffle right into the sink opening by pushing it right into the sink till it snaps into location.
13. Test the garbage disposal.
For all designs, you need to test for leakages at the sink flange, dish washer, tail-pipe and installing assembly connections. Ultimately, turn on the electrical breaker to check its operation.
Garbage Disposal installation for brand-new homes in Carson
How to Install a Garbage Disposal in Carson