1. Switch off power to the garbage disposal as well as separate the down trap.
Shut off the electric power at the circuit box or breaker. Then, utilizing flexible pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing setting up.
Support the garbage disposal with one hand and also insert completion of the wrenchette or screwdriver right into the appropriate side of one placing lug on the lower mounting ring. Lift the garbage disposal a little and loosen up the lower installing ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the installing setting up.
3. Detach the electrical.
Lay the garbage disposal on its side and get rid of the electrical cover plate from the bottom. Loosen the eco-friendly ground screw and also get rid of cable connectors. Separate garbage disposal cords from electrical supply cords. Loosen screws on the electrical clamp connector and remove cables from the garbage disposal.
4. Eliminate existing installing equipment if hardware substitute needed. Or else miss to step 12.
To get rid of the existing installing hardware, loosen the 3 placing screws, tear the breeze ring off with a screwdriver as well as get rid of the old mounting setting up.
5. Remove the old sink flange and also putty.
Press the old sink flange up through the sink hole. Utilize a screwdriver or putty blade to very carefully scrape all old putty from the side of the sink hole
. Install the brand-new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange into the drainpipe opening and press it into area. Positioning a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in place while placing the sink flange to the sink. To avoid scraping your sink or the flange, place a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and also installing flange over the sink flange. Hold these pieces in position.
7. Eliminate the dishwasher ko plug.
If making use of a dish washer, you will certainly require to tap out the dishwasher ko plug. Lay the garbage disposal on its side and use a screwdriver as well as hammer to tap it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
8. Connect the electric.
Hardwired Device:
Transform the garbage disposal over and get rid of electrical cover plate. Take out cables. Insert wire adapter (not included) and also run electric cord via accessibility opening on base of garbage disposal. Tighten cord adapter. Press cords into garbage disposal (do not displace cardboard guard) and also change electric cover plate.
If you have a hardwired device and also you’re looking to affix a cord, you will certainly require a power cable kit.
Corded System:
For a garbage disposal with a factory-installed cord, just plug in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the reduced placing ring until all 3 tabs are secured into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Insert the discharge tube.
Place the discharge tube into the discharge coupler, after that glide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drain catch.
Turn the garbage disposal so that the discharge tube is aligned with the drainpipe catch. If the discharge tube is also long, cut off as long as essential. If it is too brief, you can buy an extension.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dishwashing machine, it may be connected with an air void. Use a hose pipe clamp to attach the drainpipe hose pipe to the dishwasher inlet. Now that whatever is set up as well as in position, lock the garbage disposal to the sink installing setting up utilizing the wrenchette that came with the unit. For Evolution designs, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink until it snaps right into place.
13. Check the garbage disposal.
For all models, you need to evaluate for leaks at the sink flange, dishwasher, tail-pipe and also placing assembly connections. Ultimately, turn on the electric breaker to check its procedure.
Installing a New Garbage Disposal in Ladera Ranch