1. Turn off power to the garbage disposal as well as disconnect the down trap.
Switch off the electric power at the fuse box or circuit breaker. Then, utilizing flexible pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and place the end of the wrenchette or screwdriver right into the ideal side of one installing lug on the lower placing ring. Lift the garbage disposal slightly as well as loosen up the lower installing ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is without the installing setting up.
3. Separate the electrical.
Lay the garbage disposal on its side as well as get rid of the electrical cover plate from the bottom. Loosen up the environment-friendly ground screw as well as remove cable connectors. Separate garbage disposal cords from electrical supply cords. Loosen screws on the electrical clamp port as well as get rid of cables from the garbage disposal.
4. Eliminate existing installing hardware if equipment substitute required. Otherwise skip to step 12.
To eliminate the existing installing hardware, loosen the three placing screws, tear the breeze ring off with a screwdriver and eliminate the old mounting setting up.
5. Eliminate the old sink flange as well as putty.
Press the old sink flange up with the sink hole. Make use of a screwdriver or putty blade to carefully scratch all old putty from the side of the sink opening
. Install the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drain opening in the sink. Go down the new sink flange into the drain opening and press it into location. Placing a weight, such as the garbage disposal, in addition to the sink flange will help hold the sink flange in position while placing the sink flange to the sink. To prevent damaging your sink or the flange, put a towel between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange as well as installing flange over the sink flange. Hold these pieces in place.
7. Get rid of the dishwashing machine knockout plug.
If utilizing a dish washer, you will certainly require to tap out the dishwasher knockout plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to tap it out. Next, get rid of the loosened ko plug from inside the garbage disposal.
8. Link the electric.
Hardwired Device:
Transform the garbage disposal over as well as remove electric cover plate. Pull out wires. Put wire port (not included) and run electric cable through gain access to opening on bottom of garbage disposal. Tighten cable television connector. Press cords right into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired system as well as you’re aiming to affix a cord, you will need a power cord package.
Corded System:
For a garbage disposal with a factory-installed cord, just connect in to the outlet under your sink after completing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the lower installing ring up until all three tabs are locked into the mounting setting up. The garbage disposal will certainly currently hang by itself.
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then slide the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain catch.
Revolve the garbage disposal to make sure that the discharge tube is straightened with the drain trap. If the discharge tube is also long, removed as much as necessary. If it is as well short, you can buy an expansion.
12. Lock the garbage disposal in position.
If you are connecting the garbage disposal to a dishwashing machine, it might be connected via an air space. Make use of a hose clamp to connect the drain tube to the dishwashing machine inlet. Now that every little thing is set up and also ready, secure the garbage disposal to the sink placing setting up utilizing the wrenchette that featured the system. For Advancement versions, place the Quiet Collar ® Sink Baffle right into the sink opening by pressing it right into the sink up until it breaks right into place.
13. Evaluate the garbage disposal.
For all versions, you ought to evaluate for leaks at the sink flange, dishwasher, tail-pipe and placing assembly links. Lastly, activate the electrical breaker to test its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Mission Viejo
What to Think About During Garbage Disposal Installation in Mission Viejo