1. Shut off power to the garbage disposal and also detach the down catch.
Switch off the electrical power at the fuse box or breaker. Then, utilizing adjustable pliers, separate the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the installing assembly.
Support the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the best side of one mounting lug on the reduced mounting ring. Raise the garbage disposal slightly and loosen the reduced placing ring by pressing or drawing the wrenchette or screwdriver to the left till the garbage disposal is free from the installing assembly.
3. Detach the electric.
Lay the garbage disposal on its side as well as eliminate the electrical cover plate from the bottom. Loosen up the green ground screw and also get rid of wire ports. Separate garbage disposal wires from electric supply wires. Loosen screws on the electric clamp connector as well as get rid of cables from the garbage disposal.
4. Eliminate existing mounting hardware if hardware replacement needed. Otherwise avoid to step 12.
To eliminate the existing placing hardware, loosen the three mounting screws, pry the breeze ring off with a screwdriver as well as remove the old placing assembly.
5. Eliminate the old sink flange and also putty.
Press the old sink flange up through the sink hole. Use a screwdriver or putty knife to thoroughly scuff all old putty from the edge of the sink opening
. Set up the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing’s putty around the drain opening in the sink. Go down the brand-new sink flange right into the drain opening and also press it right into area. Putting a weight, such as the garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in position while mounting the sink flange to the sink. To avoid scratching your sink or the flange, position a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange as well as mounting flange over the sink flange. Hold these pieces in place.
7. Get rid of the dish washer ko plug.
If using a dishwashing machine, you will certainly require to touch out the dishwasher knockout plug. Lay the garbage disposal on its side and make use of a screwdriver as well as hammer to touch it out. Next, get rid of the loosened knockout plug from inside the garbage disposal.
8. Attach the electrical.
Transform the garbage disposal over as well as remove electrical cover plate. Pull out cords. Insert cord adapter (not consisted of) and also run electric wire through accessibility hole on base of garbage disposal. Tighten cord connector. Push cables into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired system as well as you’re seeking to attach a cable, you will certainly require a power cable set.
For a garbage disposal with a factory-installed cable, merely connect in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in place, transform the reduced mounting ring up until all 3 tabs are locked right into the mounting setting up. The garbage disposal will certainly now hang on its own.
10. Put the discharge tube.
Put the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube as well as setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe catch.
Rotate the garbage disposal so that the discharge tube is lined up with the drainpipe trap. If the discharge tube is too long, cut off as long as required. If it is also brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwasher, it may be attached through an air space. Use a pipe clamp to attach the drain hose pipe to the dishwasher inlet. Since whatever is mounted as well as ready, secure the garbage disposal to the sink placing assembly using the wrenchette that included the system. For Evolution versions, insert the Quiet Collar ® Sink Baffle right into the sink opening by pushing it into the sink up until it breaks right into location.
13. Check the garbage disposal.
For all models, you ought to examine for leakages at the sink flange, dish washer, tail-pipe as well as mounting assembly links. Lastly, turn on the electric breaker to test its operation.
How to Choose a Garbage Disposal in North Hollywood
Garbage Disposal Installation: An Environmental and Cost Effective Option in North Hollywood