1. Turn off power to the garbage disposal and also detach the down trap.
Shut off the electric power at the circuit box or breaker. After that, utilizing adjustable pliers, detach the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also insert the end of the wrenchette or screwdriver into the right side of one installing lug on the reduced placing ring. Lift the garbage disposal somewhat as well as loosen up the lower mounting ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is without the mounting setting up.
3. Disconnect the electrical.
Lay the garbage disposal on its side and get rid of the electric cover plate from the bottom. Loosen up the environment-friendly ground screw and eliminate wire ports. Detach garbage disposal wires from electrical supply cords. Loosen up screws on the electrical clamp connector as well as remove cords from the garbage disposal.
4. Eliminate existing placing hardware if equipment replacement required. Otherwise skip to tip 12.
To remove the existing placing hardware, loosen up the three mounting screws, tear the breeze ring off with a screwdriver as well as remove the old placing setting up.
5. Get rid of the old sink flange and putty.
Press the old sink flange up with the sink hole. Utilize a screwdriver or putty blade to very carefully scratch all old putty from the side of the sink hole
. Install the new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumbing technician’s putty around the drain opening in the sink. Go down the brand-new sink flange right into the drain opening and also press it right into place. Placing a weight, such as the garbage disposal, in addition to the sink flange will certainly help hold the sink flange in place while mounting the sink flange to the sink. To stay clear of scraping your sink or the flange, put a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in position.
7. Remove the dishwashing machine ko plug.
If using a dishwasher, you will require to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side as well as use a screwdriver and hammer to touch it out. Next, remove the loosened ko plug from inside the garbage disposal.
8. Link the electrical.
Hardwired System:
Transform the garbage disposal over as well as remove electrical cover plate. Take out cords. Put cable television adapter (not consisted of) and also run electric cable television through access hole on bottom of garbage disposal. Tighten cable television port. Push cords right into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired unit and you’re aiming to connect a cord, you will require a power cable set.
Corded System:
For a garbage disposal with a factory-installed cord, simply plug in to the electrical outlet under your sink after finishing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three installing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the reduced mounting ring up until all 3 tabs are locked into the installing setting up. The garbage disposal will now hang on its own.
10. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, after that slide the clamp over the discharge tube and placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Turn the garbage disposal to ensure that the discharge tube is lined up with the drainpipe trap. If the discharge tube is also long, cut off as long as required. If it is as well short, you can acquire an expansion.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwasher, it might be connected with an air gap. Utilize a tube clamp to affix the drain tube to the dishwashing machine inlet. Now that whatever is mounted as well as ready, secure the garbage disposal to the sink placing assembly utilizing the wrenchette that featured the system. For Evolution models, put the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink till it snaps right into place.
13. Check the garbage disposal.
For all models, you must check for leakages at the sink flange, dish washer, tail-pipe and placing setting up connections. Lastly, switch on the electric breaker to test its procedure.
Garbage Disposal Installation: An Environmental and Economical Solution in Pacoima