1. Shut off power to the garbage disposal and also detach the down catch.
Shut off the electrical power at the circuit box or breaker. After that, utilizing adjustable pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand as well as put completion of the wrenchette or screwdriver right into the right side of one mounting lug on the reduced installing ring. Raise the garbage disposal slightly as well as loosen up the lower placing ring by pushing or drawing the wrenchette or screwdriver to the left until the garbage disposal is devoid of the mounting setting up.
3. Detach the electrical.
Lay the garbage disposal on its side as well as get rid of the electrical cover plate from all-time low. Loosen up the environment-friendly ground screw and also remove cord connectors. Detach garbage disposal cables from electric supply wires. Loosen up screws on the electric clamp connector and also get rid of cables from the garbage disposal.
4. Remove existing placing equipment if equipment substitute required. Or else skip to tip 12.
To get rid of the existing placing hardware, loosen up the three placing screws, pry the snap ring off with a screwdriver and eliminate the old mounting setting up.
5. Eliminate the old sink flange and putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty knife to carefully scratch all old putty from the side of the sink hole
. Set up the brand-new sink flange, gasket as well as rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drain opening in the sink. Drop the new sink flange right into the drainpipe opening and also press it into area. Putting a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while placing the sink flange to the sink. To stay clear of scraping your sink or the flange, position a towel in between the sink surface and the weight. From under the sink, slide the fiber gasket, backup flange and installing flange over the sink flange. Hold these items in position.
7. Remove the dishwashing machine ko plug.
If making use of a dishwasher, you will certainly require to touch out the dish washer ko plug. Lay the garbage disposal on its side and also make use of a screwdriver as well as hammer to touch it out. Next off, remove the loose knockout plug from inside the garbage disposal.
8. Link the electrical.
Hardwired System:
Turn the garbage disposal over as well as remove electrical cover plate. Take out cords. Put cable television adapter (not included) and run electrical cable via gain access to hole on base of garbage disposal. Tighten cord port. Push wires into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired system as well as you’re seeking to affix a cable, you will need a power cable package.
Corded Device:
For a garbage disposal with a factory-installed cord, just plug in to the outlet under your sink after finishing the remainder of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the reduced mounting ring till all 3 tabs are secured right into the installing assembly. The garbage disposal will certainly currently hang on its own.
10. Place the discharge tube.
Place the discharge tube right into the discharge coupler, then slide the clamp over the discharge tube and also placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drainpipe catch.
Rotate the garbage disposal to ensure that the discharge tube is lined up with the drain catch. If the discharge tube is as well long, cut off as long as essential. If it is as well brief, you can buy an expansion.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwasher, it may be linked via an air void. Utilize a pipe clamp to affix the drain pipe to the dishwasher inlet. Now that every little thing is installed and also ready, secure the garbage disposal to the sink installing setting up making use of the wrenchette that featured the device. For Development models, place the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink until it snaps right into location.
13. Test the garbage disposal.
For all versions, you ought to check for leaks at the sink flange, dishwashing machine, tail-pipe as well as placing assembly connections. Lastly, activate the electrical breaker to test its procedure.
Ways to Install a Garbage Disposal in Rancho Santa Margarita
Garbage Disposal installation for brand-new homes in Rancho Santa Margarita