1. Shut off power to the garbage disposal and also detach the down trap.
Switch off the electric power at the circuit box or circuit breaker. After that, utilizing flexible pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Assistance the garbage disposal with one hand and place completion of the wrenchette or screwdriver right into the best side of one mounting lug on the lower placing ring. Raise the garbage disposal a little and loosen the lower mounting ring by pushing or pulling the wrenchette or screwdriver to the left until the garbage disposal is free from the placing assembly.
3. Disconnect the electric.
Lay the garbage disposal on its side and also remove the electric cover plate from all-time low. Loosen up the eco-friendly ground screw as well as remove cable adapters. Disconnect garbage disposal wires from electrical supply cords. Loosen up screws on the electrical clamp connector and also remove cords from the garbage disposal.
4. Remove existing mounting hardware if hardware substitute required. Or else skip to tip 12.
To remove the existing installing hardware, loosen the three placing screws, tear the snap ring off with a screwdriver and also eliminate the old placing setting up.
5. Eliminate the old sink flange and putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty knife to carefully scrape all old putty from the side of the sink hole
. Mount the brand-new sink flange, gasket and rings.
Location a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Drop the new sink flange into the drain opening as well as press it right into area. Putting a weight, such as the garbage disposal, on top of the sink flange will certainly assist hold the sink flange in position while placing the sink flange to the sink. To prevent damaging your sink or the flange, put a towel in between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange and also installing flange over the sink flange. Hold these items in place.
7. Get rid of the dishwasher knockout plug.
If using a dishwashing machine, you will certainly need to touch out the dishwashing machine knockout plug. Lay the garbage disposal on its side as well as make use of a screwdriver as well as hammer to tap it out. Next, get rid of the loose knockout plug from inside the garbage disposal.
8. Link the electric.
Turn the garbage disposal over as well as remove electric cover plate. Pull out wires. Place cable port (not included) and run electric cable with gain access to opening on bottom of garbage disposal. Tighten up cord connector. Press wires into garbage disposal (do not displace cardboard guard) and replace electrical cover plate.
If you have a hardwired unit and also you’re seeking to attach a cable, you will require a power cable package.
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the 3 placing tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, transform the lower mounting ring till all 3 tabs are locked right into the mounting assembly. The garbage disposal will certainly now hang on its own.
10. Place the discharge tube.
Place the discharge tube into the discharge coupler, after that move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Rotate the garbage disposal to ensure that the discharge tube is lined up with the drainpipe catch. If the discharge tube is as well long, removed as much as required. If it is too brief, you can acquire an extension.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwashing machine, it might be linked with an air void. Use a tube clamp to connect the drain pipe to the dishwashing machine inlet. Now that every little thing is set up and ready, secure the garbage disposal to the sink placing assembly utilizing the wrenchette that featured the device. For Advancement versions, insert the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink till it snaps right into location.
13. Test the garbage disposal.
For all versions, you must evaluate for leakages at the sink flange, dishwasher, tail-pipe and installing setting up links. Lastly, switch on the electrical breaker to examine its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Sylmar
New Garbage Disposal Installation Guide in Sylmar