1. Shut off power to the garbage disposal and also detach the down trap.
Switch off the electric power at the fuse box or circuit breaker. Then, utilizing adjustable pliers, separate the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing setting up.
Support the garbage disposal with one hand and also place the end of the wrenchette or screwdriver right into the ideal side of one installing lug on the lower installing ring. Raise the garbage disposal a little and also loosen up the reduced mounting ring by pressing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the installing assembly.
3. Disconnect the electric.
Lay the garbage disposal on its side and remove the electrical cover plate from the bottom. Loosen the environment-friendly ground screw as well as get rid of wire adapters. Separate garbage disposal cords from electric supply wires. Loosen up screws on the electric clamp connector as well as get rid of cords from the garbage disposal.
4. Remove existing mounting equipment if equipment substitute needed. Otherwise skip to tip 12.
To eliminate the existing installing equipment, loosen up the three mounting screws, tear the breeze ring off with a screwdriver as well as get rid of the old placing setting up.
5. Remove the old sink flange and putty.
Push the old sink flange up with the sink hole. Make use of a screwdriver or putty blade to very carefully scratch all old putty from the side of the sink opening
. Install the new sink flange, gasket and also rings.
Place a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange into the drainpipe opening as well as press it right into area. Putting a weight, such as the garbage disposal, on top of the sink flange will certainly help hold the sink flange in place while mounting the sink flange to the sink. To prevent scratching your sink or the flange, place a towel in between the sink surface and also the weight. From under the sink, slide the fiber gasket, backup flange as well as mounting flange over the sink flange. Hold these items in position.
7. Eliminate the dishwashing machine knockout plug.
If utilizing a dishwasher, you will certainly require to touch out the dish washer ko plug. Lay the garbage disposal on its side as well as use a screwdriver and hammer to tap it out. Next, eliminate the loose ko plug from inside the garbage disposal.
8. Link the electric.
Turn the garbage disposal over and get rid of electrical cover plate. Take out cords. Insert cable television port (not consisted of) and also run electrical cable via accessibility hole on base of garbage disposal. Tighten cable connector. Push cords right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired device as well as you’re looking to affix a cable, you will need a power cord set.
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after finishing the rest of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 mounting tabs with the slide-up ramps on the mounting ring. Holding the garbage disposal in position, turn the lower installing ring till all three tabs are locked right into the placing setting up. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Place the discharge tube into the discharge coupler, then slide the clamp over the discharge tube as well as placement it in the groove on the rubber tailpipe coupler.
11. Line up the discharge tube with the drain trap.
Revolve the garbage disposal so that the discharge tube is lined up with the drain trap. If the discharge tube is too long, cut off as long as necessary. If it is also short, you can buy an expansion.
12. Lock the garbage disposal in place.
If you are attaching the garbage disposal to a dishwashing machine, it might be linked through an air gap. Use a pipe clamp to attach the drain pipe to the dishwasher inlet. Now that every little thing is mounted and in position, secure the garbage disposal to the sink mounting assembly making use of the wrenchette that included the device. For Evolution versions, put the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink until it breaks into location.
13. Check the garbage disposal.
For all designs, you must check for leakages at the sink flange, dishwashing machine, tail-pipe as well as mounting assembly connections. Finally, activate the electrical breaker to examine its operation.
What to Think About During Garbage Disposal Installation in Lytle Creek
DIY Garbage Disposal Installation in Lytle Creek