1. Shut off power to the garbage disposal as well as detach the down trap.
Turn off the electrical power at the circuit box or circuit breaker. Then, making use of flexible pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting setting up.
Assistance the garbage disposal with one hand as well as put the end of the wrenchette or screwdriver into the appropriate side of one installing lug on the lower placing ring. Raise the garbage disposal slightly and also loosen up the lower installing ring by pushing or drawing the wrenchette or screwdriver to the left up until the garbage disposal is devoid of the installing assembly.
3. Disconnect the electric.
Lay the garbage disposal on its side and eliminate the electrical cover plate from the bottom. Loosen the environment-friendly ground screw and eliminate cord ports. Disconnect garbage disposal cables from electrical supply wires. Loosen up screws on the electric clamp adapter and also get rid of wires from the garbage disposal.
4. Eliminate existing placing equipment if hardware replacement required. Or else skip to tip 12.
To eliminate the existing installing equipment, loosen up the three placing screws, pry the breeze ring off with a screwdriver and also get rid of the old mounting setting up.
5. Eliminate the old sink flange and also putty.
Press the old sink flange up through the sink hole. Make use of a screwdriver or putty blade to carefully scratch all old putty from the side of the sink hole
. Install the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumber’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange right into the drainpipe opening as well as press it right into place. Putting a weight, such as the garbage disposal, on top of the sink flange will aid hold the sink flange in place while mounting the sink flange to the sink. To stay clear of scraping your sink or the flange, place a towel between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange and installing flange over the sink flange. Hold these pieces in position.
7. Eliminate the dish washer knockout plug.
If using a dish washer, you will certainly require to tap out the dishwashing machine ko plug. Lay the garbage disposal on its side and use a screwdriver and hammer to tap it out. Next off, get rid of the loosened knockout plug from inside the garbage disposal.
8. Attach the electric.
Hardwired System:
Turn the garbage disposal over and get rid of electrical cover plate. Take out cords. Put wire adapter (not consisted of) as well as run electrical cable with accessibility opening on base of garbage disposal. Tighten cord adapter. Press cables into garbage disposal (do not displace cardboard shield) and also replace electrical cover plate.
If you have a hardwired system and also you’re looking to attach a cord, you will certainly require a power cord package.
Corded Device:
For a garbage disposal with a factory-installed cable, just plug in to the electrical outlet under your sink after completing the rest of the steps.
9. Hang the garbage disposal.
Hang the garbage disposal by aligning the 3 mounting tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, transform the reduced mounting ring until all three tabs are secured right into the installing assembly. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Place the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube and position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe trap.
Rotate the garbage disposal so that the discharge tube is straightened with the drainpipe trap. If the discharge tube is too long, removed as high as required. If it is as well short, you can buy an extension.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dishwashing machine, it may be connected through an air space. Utilize a hose clamp to affix the drainpipe hose pipe to the dishwasher inlet. Now that whatever is installed as well as ready, secure the garbage disposal to the sink placing setting up using the wrenchette that featured the system. For Advancement designs, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink up until it breaks into location.
13. Test the garbage disposal.
For all versions, you need to test for leaks at the sink flange, dish washer, tail-pipe and also mounting assembly connections. Finally, switch on the electric breaker to evaluate its procedure.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in South Pasadena
How to Choose a Garbage Disposal in South Pasadena