1. Turn off power to the garbage disposal and detach the down catch.
Shut off the electric power at the fuse box or breaker. Then, using adjustable pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand and also put completion of the wrenchette or screwdriver right into the right side of one placing lug on the lower installing ring. Lift the garbage disposal a little as well as loosen up the reduced mounting ring by pressing or pulling the wrenchette or screwdriver to the left until the garbage disposal is devoid of the mounting assembly.
3. Separate the electric.
Lay the garbage disposal on its side and eliminate the electric cover plate from all-time low. Loosen up the eco-friendly ground screw as well as eliminate cable adapters. Separate garbage disposal cords from electric supply cords. Loosen screws on the electrical clamp adapter as well as eliminate cords from the garbage disposal.
4. Get rid of existing placing hardware if hardware replacement needed. Or else miss to tip 12.
To eliminate the existing mounting equipment, loosen up the 3 mounting screws, tear the snap ring off with a screwdriver and eliminate the old installing setting up.
5. Eliminate the old sink flange and putty.
Press the old sink flange up through the sink hole. Use a screwdriver or putty knife to thoroughly scrape all old putty from the edge of the sink hole
. Set up the new sink flange, gasket and rings.
Area a 1/2 inch rope of plumbing’s putty around the drainpipe opening in the sink. Go down the new sink flange right into the drainpipe opening and also press it right into location. Positioning a weight, such as the garbage disposal, in addition to the sink flange will certainly assist hold the sink flange in position while mounting the sink flange to the sink. To stay clear of scratching your sink or the flange, place a towel in between the sink surface area and also the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in place.
7. Remove the dishwasher knockout plug.
If utilizing a dishwashing machine, you will certainly need to touch out the dish washer ko plug. Lay the garbage disposal on its side and utilize a screwdriver as well as hammer to touch it out. Next off, remove the loosened knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Device:
Turn the garbage disposal over and also remove electric cover plate. Pull out wires. Insert wire adapter (not consisted of) and run electrical wire with gain access to hole on base of garbage disposal. Tighten wire port. Press cords into garbage disposal (do not displace cardboard shield) and also change electric cover plate.
If you have a hardwired system and also you’re aiming to connect a cable, you will need a power cord set.
Corded System:
For a garbage disposal with a factory-installed cord, just plug in to the electrical outlet under your sink after finishing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by straightening the three placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the reduced placing ring up until all 3 tabs are locked into the placing setting up. The garbage disposal will currently hang on its own.
10. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, after that slide the clamp over the discharge tube and setting it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe trap.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain trap. If the discharge tube is also long, removed as long as necessary. If it is as well brief, you can buy an expansion.
12. Lock the garbage disposal in position.
If you are attaching the garbage disposal to a dish washer, it may be connected with an air gap. Utilize a tube clamp to connect the drain tube to the dish washer inlet. Now that whatever is set up as well as ready, lock the garbage disposal to the sink mounting setting up utilizing the wrenchette that featured the device. For Advancement designs, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it right into the sink until it breaks into place.
13. Examine the garbage disposal.
For all versions, you ought to evaluate for leakages at the sink flange, dishwashing machine, tail-pipe and mounting assembly connections. Lastly, activate the electrical breaker to evaluate its operation.
What to Think About During Garbage Disposal Installation in Atwood
Starting a Garbage Disposal Installation Project in Atwood