1. Turn off power to the garbage disposal and separate the down catch.
Turn off the electrical power at the circuit box or circuit breaker. Then, making use of flexible pliers, detach the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Support the garbage disposal with one hand as well as place completion of the wrenchette or screwdriver right into the right side of one mounting lug on the lower mounting ring. Lift the garbage disposal somewhat and also loosen the reduced mounting ring by pressing or drawing the wrenchette or screwdriver to the left till the garbage disposal is devoid of the installing assembly.
3. Separate the electrical.
Lay the garbage disposal on its side and also get rid of the electrical cover plate from the bottom. Loosen up the eco-friendly ground screw as well as eliminate cord connectors. Disconnect garbage disposal wires from electric supply cords. Loosen up screws on the electrical clamp adapter and get rid of cords from the garbage disposal.
4. Eliminate existing placing hardware if hardware replacement required. Or else avoid to tip 12.
To eliminate the existing mounting hardware, loosen up the three placing screws, tear the breeze ring off with a screwdriver and remove the old installing assembly.
5. Remove the old sink flange and also putty.
Press the old sink flange up with the sink hole. Make use of a screwdriver or putty knife to meticulously scratch all old putty from the edge of the sink hole
. Set up the brand-new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumbing technician’s putty around the drainpipe opening in the sink. Drop the new sink flange right into the drainpipe opening and also press it right into location. Putting a weight, such as the garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in place while placing the sink flange to the sink. To stay clear of scratching your sink or the flange, position a towel in between the sink surface area as well as the weight. From under the sink, slide the fiber gasket, back-up flange and also mounting flange over the sink flange. Hold these items in position.
7. Eliminate the dish washer ko plug.
If utilizing a dishwasher, you will require to touch out the dish washer ko plug. Lay the garbage disposal on its side as well as utilize a screwdriver and hammer to tap it out. Next off, get rid of the loose ko plug from inside the garbage disposal.
8. Connect the electrical.
Hardwired Unit:
Turn the garbage disposal over and also remove electrical cover plate. Pull out cables. Put cable television adapter (not included) as well as run electric cable with gain access to opening on bottom of garbage disposal. Tighten cable connector. Push cables into garbage disposal (do not displace cardboard shield) and replace electrical cover plate.
If you have a hardwired system and you’re looking to affix a cord, you will certainly require a power cable package.
Corded System:
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the reduced installing ring till all 3 tabs are secured into the mounting assembly. The garbage disposal will now hang by itself.
10. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drain trap.
Revolve the garbage disposal so that the discharge tube is straightened with the drainpipe catch. If the discharge tube is as well long, cut off as high as essential. If it is also short, you can purchase an expansion.
12. Lock the garbage disposal in place.
If you are connecting the garbage disposal to a dish washer, it may be attached with an air void. Use a hose clamp to affix the drain pipe to the dishwasher inlet. Since everything is installed and in position, lock the garbage disposal to the sink placing setting up making use of the wrenchette that included the device. For Development models, place the Quiet Collar ® Sink Baffle into the sink opening by pressing it into the sink until it snaps right into area.
13. Check the garbage disposal.
For all designs, you must check for leakages at the sink flange, dishwasher, tail-pipe and installing assembly links. Finally, activate the electric breaker to test its operation.
Plumbing Service – Repair and replacement – Garbage Disposal Installation in Norco
New Garbage Disposal Installation Guide in Norco