1. Shut off power to the garbage disposal as well as disconnect the down trap.
Shut off the electric power at the circuit box or circuit breaker. Then, utilizing flexible pliers, disconnect the drain top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the mounting assembly.
Assistance the garbage disposal with one hand as well as insert completion of the wrenchette or screwdriver right into the best side of one mounting lug on the lower mounting ring. Raise the garbage disposal a little and loosen up the lower placing ring by pressing or pulling the wrenchette or screwdriver to the left till the garbage disposal is devoid of the placing setting up.
3. Detach the electric.
Lay the garbage disposal on its side as well as remove the electrical cover plate from the bottom. Loosen up the green ground screw as well as remove cord connectors. Disconnect garbage disposal cables from electrical supply cables. Loosen up screws on the electric clamp port and also eliminate wires from the garbage disposal.
4. Eliminate existing placing hardware if hardware substitute required. Otherwise miss to tip 12.
To eliminate the existing mounting equipment, loosen up the three mounting screws, tear the snap ring off with a screwdriver and eliminate the old placing assembly.
5. Eliminate the old sink flange and putty.
Push the old sink flange up via the sink hole. Make use of a screwdriver or putty blade to meticulously scrape all old putty from the edge of the sink opening
. Mount the new sink flange, gasket and also rings.
Area a 1/2 inch rope of plumbing professional’s putty around the drain opening in the sink. Drop the brand-new sink flange right into the drainpipe opening as well as press it into area. Positioning a weight, such as the garbage disposal, on top of the sink flange will aid hold the sink flange in place while installing the sink flange to the sink. To avoid damaging your sink or the flange, put a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, back-up flange and placing flange over the sink flange. Hold these items in position.
7. Eliminate the dish washer ko plug.
If using a dishwasher, you will require to tap out the dishwasher ko plug. Lay the garbage disposal on its side and make use of a screwdriver and also hammer to tap it out. Next off, eliminate the loose knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired System:
Turn the garbage disposal over as well as remove electric cover plate. Take out cables. Place wire port (not consisted of) and run electrical wire via accessibility hole on base of garbage disposal. Tighten cable television port. Push wires right into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired system and also you’re seeking to attach a cable, you will require a power cord set.
Corded Device:
For a garbage disposal with a factory-installed cable, just plug in to the electrical outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 installing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the lower placing ring up until all three tabs are locked into the placing assembly. The garbage disposal will certainly currently hang by itself.
10. Place the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
11. Align the discharge tube with the drainpipe catch.
Revolve the garbage disposal to make sure that the discharge tube is aligned with the drain catch. If the discharge tube is as well long, removed as high as essential. If it is also short, you can purchase an extension.
12. Lock the garbage disposal in place.
If you are linking the garbage disposal to a dishwashing machine, it may be linked through an air void. Make use of a hose clamp to attach the drain tube to the dish washer inlet. Since every little thing is installed and in position, secure the garbage disposal to the sink mounting setting up using the wrenchette that came with the system. For Advancement models, place the Quiet Collar ® Sink Baffle right into the sink opening by pressing it into the sink until it breaks into location.
13. Test the garbage disposal.
For all versions, you need to check for leakages at the sink flange, dishwasher, tail-pipe and installing assembly links. Ultimately, turn on the electric breaker to evaluate its procedure.
Every little thing You Need to Find Out About Waste Disposals in Santa Clarita
Installing a New Garbage Disposal in Santa Clarita