1. Switch off power to the garbage disposal and disconnect the down catch.
Shut off the electric power at the fuse box or circuit breaker. Then, using adjustable pliers, disconnect the drainpipe top from the garbage disposal waste discharge tube.
2. Free the garbage disposal from the placing assembly.
Support the garbage disposal with one hand and put the end of the wrenchette or screwdriver right into the ideal side of one mounting lug on the reduced mounting ring. Lift the garbage disposal somewhat and loosen the reduced placing ring by pushing or drawing the wrenchette or screwdriver to the left till the garbage disposal is free from the placing setting up.
3. Separate the electrical.
Lay the garbage disposal on its side and also get rid of the electric cover plate from the bottom. Loosen up the green ground screw as well as get rid of cable ports. Disconnect garbage disposal wires from electric supply wires. Loosen up screws on the electrical clamp port and get rid of cords from the garbage disposal.
4. Eliminate existing installing equipment if equipment substitute needed. Or else skip to step 12.
To get rid of the existing installing hardware, loosen up the 3 mounting screws, pry the breeze ring off with a screwdriver and also eliminate the old placing setting up.
5. Remove the old sink flange as well as putty.
Press the old sink flange up with the sink hole. Utilize a screwdriver or putty blade to carefully scrape all old putty from the edge of the sink opening
. Mount the new sink flange, gasket as well as rings.
Location a 1/2 inch rope of plumber’s putty around the drain opening in the sink. Drop the new sink flange into the drain opening as well as press it into location. Putting a weight, such as the garbage disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To prevent scratching your sink or the flange, position a towel in between the sink surface as well as the weight. From under the sink, slide the fiber gasket, back-up flange as well as mounting flange over the sink flange. Hold these items in position.
7. Get rid of the dish washer knockout plug.
If using a dishwasher, you will certainly need to tap out the dishwasher ko plug. Lay the garbage disposal on its side and also use a screwdriver and also hammer to touch it out. Next off, eliminate the loosened knockout plug from inside the garbage disposal.
8. Link the electric.
Hardwired Unit:
Turn the garbage disposal over as well as get rid of electric cover plate. Take out cords. Place cable adapter (not consisted of) as well as run electrical wire through accessibility hole on bottom of garbage disposal. Tighten up cord adapter. Push wires into garbage disposal (do not displace cardboard shield) and also change electrical cover plate.
If you have a hardwired unit as well as you’re aiming to connect a cable, you will certainly need a power cable kit.
Corded System:
For a garbage disposal with a factory-installed cable, simply plug in to the outlet under your sink after completing the remainder of the actions.
9. Hang the garbage disposal.
Hang the garbage disposal by lining up the three placing tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the lower placing ring until all three tabs are secured into the installing setting up. The garbage disposal will certainly now hang by itself.
10. Put the discharge tube.
Put the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube as well as position it in the groove on the rubber tailpipe coupler.
11. Straighten the discharge tube with the drainpipe catch.
Turn the garbage disposal to make sure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is as well long, removed as long as necessary. If it is also brief, you can purchase an extension.
12. Lock the garbage disposal in position.
If you are linking the garbage disposal to a dishwashing machine, it may be attached through an air space. Use a pipe clamp to attach the drain tube to the dishwashing machine inlet. Now that every little thing is installed and also ready, secure the garbage disposal to the sink placing setting up using the wrenchette that featured the system. For Advancement designs, insert the Quiet Collar ® Sink Baffle into the sink opening by pushing it into the sink until it snaps into place.
13. Evaluate the garbage disposal.
For all models, you ought to examine for leaks at the sink flange, dishwasher, tail-pipe as well as mounting assembly links. Lastly, activate the electrical breaker to evaluate its procedure.
Starting a Garbage Disposal Installation Project in Toluca Lake