1. Separate the p-trap and also the horizontal expansion pipe.
Huge channel-lock pliers or a pipe wrench work well to loosen the nuts holding the pipelines with each other. When both links are cost-free, get rid of the components. You might intend to cleanse the horizontal drain pipe to remove any kind of possible clog. (This is not necessary in new construction.).
2. Detach the down drainpipe.
Using big channel-lock pliers, disconnect the down drain coming from the sink as well as the connection that affixes it to the p-trap. When both connections are free, remove the components.
3. Unscrew the huge nut.
Loosen the huge nut that holds the filter in place beneath the sink. Remove the filter body.
4. Tear off the snap ring and clean off the old plumbing technician’s putty.
Using a flathead screwdriver, loosen up the 3 screws on the installing setting up and tear off the snap ring. Clean off the old plumbing professional’s putty that surrounds the edge of the drainpipe opening.
5. Install the new sink flange.
Area a 1/2″ rope of plumbing’s putty around the drainpipe opening in the sink. Drop the brand-new sink flange into the drain opening and press it into place. Putting a weight, such as your garbage disposal, in addition to the sink flange will certainly aid hold the sink flange in position while placing it to the sink. To prevent damaging your sink or the flange, position a towel in between the sink surface area and the weight.
6. Mount gasket and flanges.
From under the sink, slide the fiber gasket, backup flange as well as installing flange over the sink flange. Hold these items in position.
7. Slip on the placing as well as snap rings.
Next off, slip on the installing ring and snap ring. Tighten the three mounting screws, alternately tightening up each screw a few turns at a time until the placing setting up is equally and also securely seated versus the bottom of the sink.
8. Eliminate the dishwashing machine knockout plug.
If using a dishwashing machine, you will certainly need to touch out the dishwasher ko plug. Lay the garbage disposal on its side and also utilize a screwdriver and hammer to tap it out. Next, remove the loose knockout plug from inside the garbage disposal.
9. Attach the electric.
Hardwired Unit:.
Turn the garbage disposal over and also remove electric cover plate. Take out cables. Put wire adapter (not included) as well as run electrical cord through accessibility opening on base of garbage disposal. Tighten up cord connector. Push wires right into garbage disposal (do not displace cardboard guard) and change electrical cover plate.
If you have a hardwired device and you’re wanting to attach a cable, you will certainly need a power cable package.
Corded System:.
For a garbage disposal with a factory-installed cable, just plug in to the electrical outlet under your sink after finishing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by lining up the 3 placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in position, transform the reduced mounting ring up until all 3 tabs are secured into the installing setting up.
11. Insert the discharge tube.
Insert the discharge tube into the discharge coupler, then glide the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drain pipeline.
Rotate the garbage disposal to ensure that the discharge tube is aligned with the drainpipe trap. If the discharge tube is too long, cut off as a lot of the tube as needed. If it is also brief, you can purchase an extension. If you are attaching the garbage disposal to a dishwasher, it might be connected through an air space. Make use of a hose pipe clamp to attach the drainpipe tube to the dish washer inlet.
13. Lock the garbage disposal in position.
Since whatever is set up as well as ready, secure the garbage disposal to the sink installing assembly using the wrench that featured the unit. Insert the Quiet Collar Sink Baffle right into the sink opening by pushing it right into the sink up until it snaps right into location.
14. Test the garbage disposal.
Test for leaks at the sink flange, dish washer, tail-pipe and mounting setting up links. Finally, activate the electrical breaker to examine its operation. Appreciate your new garbage disposal!
How to Choose a Garbage Disposal in Duarte
How to Install a Garbage Disposal in Duarte