1. Detach the p-trap and also the straight extension pipe.
Big channel-lock pliers or a pipe wrench work well to loosen the nuts holding the pipes together. When both links are cost-free, remove the parts. You might want to clean the horizontal drain pipe to get rid of any feasible blockage. (This is not necessary in brand-new construction.).
2. Separate the down drainpipe.
Utilizing huge channel-lock pliers, disconnect the down drain originating from the sink as well as the connection that attaches it to the p-trap. When both links are cost-free, get rid of the parts.
3. Unscrew the huge nut.
Unscrew the huge nut that holds the strainer in place beneath the sink. Get rid of the strainer body.
4. Pry off the snap ring as well as wipe the old plumbing professional’s putty.
Making use of a flathead screwdriver, loosen up the 3 screws on the mounting setting up as well as pry off the snap ring. Wipe the old plumbing’s putty that surrounds the side of the drain opening.
5. Mount the new sink flange.
Area a 1/2″ rope of plumbing’s putty around the drain opening in the sink. Drop the new sink flange right into the drainpipe opening and also press it into area. Positioning a weight, such as your garbage disposal, on top of the sink flange will aid hold the sink flange in position while installing it to the sink. To prevent scraping your sink or the flange, position a towel in between the sink surface area and the weight.
6. Install gasket and flanges.
From under the sink, slide the fiber gasket, back-up flange and placing flange over the sink flange. Hold these items in place.
7. Slip on the installing and also break rings.
Next, slip on the placing ring and also break ring. Tighten up the 3 installing screws, at the same time tightening each screw a few turns each time up until the placing setting up is equally as well as securely seated versus the bottom of the sink.
8. Get rid of the dish washer ko plug.
If utilizing a dish washer, you will need to touch out the dishwashing machine ko plug. Lay the garbage disposal on its side and make use of a screwdriver and hammer to tap it out. Next, eliminate the loosened ko plug from inside the garbage disposal.
9. Connect the electrical.
Hardwired System:.
Transform the garbage disposal over and eliminate electric cover plate. Take out wires. Place cable adapter (not consisted of) and run electric wire with gain access to hole on base of garbage disposal. Tighten up cable television adapter. Push cords into garbage disposal (do not displace cardboard guard) as well as replace electrical cover plate.
If you have a hardwired device and also you’re wanting to connect a cable, you will certainly need a power cable set.
Corded Device:.
For a garbage disposal with a factory-installed cable, simply connect in to the electrical outlet under your sink after completing the remainder of the actions.
10. Hang the garbage disposal.
Hang the garbage disposal by aligning the three placing tabs with the slide-up ramps on the installing ring. Holding the garbage disposal in place, turn the lower mounting ring until all three tabs are locked into the placing setting up.
11. Place the discharge tube.
Place the discharge tube right into the discharge coupler, after that move the clamp over the discharge tube and also position it in the groove on the rubber tailpipe coupler.
12. Straighten the discharge tube with the drainpipe pipe.
Turn the garbage disposal so that the discharge tube is aligned with the drainpipe trap. If the discharge tube is as well long, cut off as a lot of the tube as necessary. If it is also brief, you can purchase an expansion. If you are linking the garbage disposal to a dishwashing machine, it might be attached through an air gap. Utilize a tube clamp to affix the drain hose to the dish washer inlet.
13. Lock the garbage disposal in place.
Since every little thing is installed as well as in position, secure the garbage disposal to the sink mounting setting up making use of the wrench that included the system. Insert the Quiet Collar Sink Baffle into the sink opening by pushing it into the sink until it snaps right into area.
14. Evaluate the garbage disposal.
Examination for leaks at the sink flange, dishwasher, tail-pipe and mounting setting up links. Ultimately, turn on the electric breaker to test its operation. Enjoy your new garbage disposal!
Whatever You Need to Understand About Waste Disposals in Santa Ana