1. Separate the p-trap as well as the horizontal extension pipe.
Big channel-lock pliers or a pipe wrench job well to loosen up the nuts holding the pipes together. When both connections are cost-free, get rid of the parts. You might wish to clean up the straight drain pipeline to eliminate any feasible obstruction. (This is not necessary in brand-new construction.).
2. Separate the down drain.
Utilizing large channel-lock pliers, detach the down drainpipe coming from the sink and the link that affixes it to the p-trap. When both connections are complimentary, get rid of the components.
3. Unscrew the large nut.
Loosen the huge nut that holds the filter in place beneath the sink. Remove the strainer body.
4. Tear off the snap ring as well as clean off the old plumber’s putty.
Making use of a flathead screwdriver, loosen up the 3 screws on the mounting setting up and pry off the breeze ring. Wipe the old plumber’s putty that surrounds the edge of the drain opening.
5. Install the new sink flange.
Location a 1/2″ rope of plumbing technician’s putty around the drain opening in the sink. Drop the brand-new sink flange into the drain opening and press it into location. Positioning a weight, such as your garbage disposal, on top of the sink flange will assist hold the sink flange in place while mounting it to the sink. To avoid scraping your sink or the flange, place a towel in between the sink surface as well as the weight.
6. Mount gasket and flanges.
From under the sink, slide the fiber gasket, backup flange and mounting flange over the sink flange. Hold these pieces in place.
7. Slip on the installing and also break rings.
Next off, slip on the mounting ring and break ring. Tighten the three installing screws, at the same time tightening up each screw a couple of turns at a time till the placing assembly is uniformly and tightly seated versus all-time low of the sink.
8. Eliminate the dish washer ko plug.
If using a dishwasher, you will require to touch out the dishwasher ko plug. Lay the garbage disposal on its side as well as use a screwdriver as well as hammer to tap it out. Next off, get rid of the loosened ko plug from inside the garbage disposal.
9. Attach the electrical.
Hardwired Device:.
Transform the garbage disposal over and also eliminate electric cover plate. Pull out cords. Insert cord port (not consisted of) as well as run electric cord through gain access to opening on base of garbage disposal. Tighten cable connector. Press cords right into garbage disposal (do not displace cardboard guard) and replace electric cover plate.
If you have a hardwired device and also you’re wanting to attach a cable, you will need a power cord set.
Corded Unit:.
For a garbage disposal with a factory-installed cable, simply plug in to the electrical outlet under your sink after completing the rest of the steps.
10. Hang the garbage disposal.
Hang the garbage disposal by straightening the three mounting tabs with the slide-up ramps on the placing ring. Holding the garbage disposal in place, transform the reduced placing ring up until all three tabs are secured into the mounting assembly.
11. Put the discharge tube.
Insert the discharge tube right into the discharge coupler, then move the clamp over the discharge tube and also setting it in the groove on the rubber tailpipe coupler.
12. Line up the discharge tube with the drainpipe pipe.
Turn the garbage disposal so that the discharge tube is aligned with the drain trap. If the discharge tube is too long, cut off as a lot of the tube as required. If it is also brief, you can purchase an expansion. If you are attaching the garbage disposal to a dish washer, it may be connected through an air void. Use a pipe clamp to attach the drain hose pipe to the dishwasher inlet.
13. Lock the garbage disposal in place.
Since every little thing is installed and ready, secure the garbage disposal to the sink placing setting up using the wrench that featured the unit. Place the Quiet Collar Sink Baffle into the sink opening by pressing it right into the sink up until it snaps right into location.
14. Check the garbage disposal.
Examination for leaks at the sink flange, dishwashing machine, tail-pipe as well as placing setting up links. Ultimately, switch on the electrical breaker to check its operation. Enjoy your brand-new garbage disposal!
New Garbage Disposal Installation Guide in Universal City
DIY Garbage Disposal Installation in Universal City